MT48LC2M32B2TG-6 Micron Technology Inc, MT48LC2M32B2TG-6 Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT48LC2M32B2TG-6
Manufacturer Part Number
MT48LC2M32B2TG-6
Description
Manufacturer
Micron Technology Inc
Type
SDRAMr
Datasheet
1.MT48LC2M32B2TG-6.pdf
(69 pages)
Specifications of MT48LC2M32B2TG-6
Organization
2Mx32
Density
64Mb
Address Bus
13b
Access Time (max)
17/7.5/5.5ns
Maximum Clock Rate
166MHz
Operating Supply Voltage (typ)
3.3V
Package Type
TSOP-II
Operating Temp Range
0C to 70C
Operating Supply Voltage (max)
3.6V
Operating Supply Voltage (min)
3V
Supply Current
180mA
Pin Count
86
Mounting
Surface Mount
Operating Temperature Classification
Commercial
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT48LC2M32B2TG-6
Manufacturer:
MICRON
Quantity:
10
Company:
Part Number:
MT48LC2M32B2TG-6
Manufacturer:
MICRON
Quantity:
5
Part Number:
MT48LC2M32B2TG-6
Manufacturer:
MICRONAS
Quantity:
20 000
Part Number:
MT48LC2M32B2TG-6:G
Manufacturer:
MT
Quantity:
20 000
Part Number:
MT48LC2M32B2TG-6D
Manufacturer:
MICRON/美光
Quantity:
20 000
Company:
Part Number:
MT48LC2M32B2TG-6G
Manufacturer:
LT
Quantity:
4 330
Part Number:
MT48LC2M32B2TG-6G
Manufacturer:
MICRON/美光
Quantity:
20 000
Part Number:
MT48LC2M32B2TG-6IT
Manufacturer:
MICRON/美光
Quantity:
20 000
PRECHARGE
Auto Precharge
BURST TERMINATE
AUTO REFRESH
SELF REFRESH
PDF: 09005aef811ce1fe/Source: 09005aef811ce1d5
64MSDRAMx32_2.fm - Rev. J 12/08 EN
The PRECHARGE command is used to deactivate the open row in a particular bank or
the open row in all banks. The bank(s) will be available for a subsequent row access a
specified time (
whether one or all banks are to be precharged, and in the case where only one bank is to
be precharged, inputs BA0 and BA1 select the bank. Otherwise BA0 and BA1 are treated
as “Don’t Care.” After a bank has been precharged, it is in the idle state and must be acti-
vated prior to any READ or WRITE commands being issued to that bank.
Auto precharge is a feature that performs the same individual-bank precharge function
described above, without requiring an explicit command. This is accomplished by using
A10 to enable auto precharge in conjunction with a specific READ or WRITE command.
A precharge of the bank/row that is addressed with the READ or WRITE command is
automatically performed upon completion of the READ or WRITE burst, except in the
full-page burst mode, where AUTO PRECHARGE does not apply. Auto precharge is
nonpersistent in that it is either enabled or disabled for each READ or WRITE command.
Auto precharge ensures that the precharge is initiated at the earliest valid stage within a
burst. The user must not issue another command to the same bank until the precharge
time (
issued at the earliest possible time, as described for each burst type in “Operations” on
page 19.
The BURST TERMINATE command is used to truncate either fixed-length or full-page
bursts. The most recently registered READ or WRITE command prior to the BURST
TERMINATE command will be truncated, as shown in “Operations” on page 19. The
BURST TERMINATE command does not precharge the row; the row will remain open
until a PRECHARGE command is issued.
AUTO REFRESH is used during normal operation of the SDRAM and is analogous to
CAS#-BEFORE-RAS# (CBR) refresh in conventional DRAMs. This command is nonper-
sistent, so it must be issued each time a refresh is required.
The addressing is generated by the internal refresh controller. This makes the address
bits “Don’t Care” during an AUTO REFRESH command. Regardless of device width, the
64Mb SDRAM requires 4,096 AUTO REFRESH cycles every 64ms (commercial and indus-
trial) or 16ms (automotive). Providing a distributed AUTO REFRESH command every
15.625
requirement and ensure that each row is refreshed. Alternatively, 4,096 AUTO REFRESH
commands can be issued in a burst at the minimum cycle rate (
(commercial and industrial) or 16ms (automotive).
The SELF REFRESH command can be used to retain data in the SDRAM, even if the rest
of the system is powered down. When in the self refresh mode, the SDRAM retains data
without external clocking. The SELF REFRESH command is initiated like an AUTO
t
µ
RP) is completed. This is determined as if an explicit PRECHARGE command was
s (commercial and industrial) or 3.906
t
RP) after the PRECHARGE command is issued. Input A10 determines
18
Micron Technology, Inc., reserves the right to change products or specifications without notice.
µ
s (automotive) will meet the refresh
©2001 Micron Technology, Inc. All rights reserved.
t
64Mb: x32 SDRAM
RFC), once every 64ms
Commands