SC16C852LIBS,151 NXP Semiconductors, SC16C852LIBS,151 Datasheet - Page 9

• Manufacturer Part Number: SC16C852LIBS,151
• Description: IC UART DUAL W/FIFO 32-HVQFN
• Manufacturer: NXP Semiconductors
• Type: IrDA or RS- 485r

Specifications of SC16C852LIBS,151

• Number Of Channels: 2, DUART
• Package / Case: 32-VFQFN Exposed Pad
• Features: Programmable
• Fifo's: 128 Byte
• Protocol: RS485
• Voltage - Supply: 1.8V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Data Rate: 5 Mbps
• Supply Voltage (max): 1.95 V
• Supply Voltage (min): 1.65 V
• Supply Current: 5 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 1.8 V
• Transmitter And Receiver Fifo Counter: Yes
• Mounting: Surface Mount
• Pin Count: 32
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-4209; 935283101151; SC16C852LIBS-S

NXP Semiconductors
Table 2.
SC16C852L
Product data sheet
Symbol
INTA/IRQ
INTB/n.c.
IOR/V
IOW/R/W
OP2A
OP2B
RESET/
RESET
RIA
RIB
RTSA
RTSB
DD
Pin description
Pin
LQFP48
30
29
19
15
32
9
36
41
21
33
22
HVQFN32 TFBGA36
22
21
14
12
-
-
24
-
-
23
15
…continued
C5
C6
F4
F3
-
-
A6
-
-
B6
F5
All information provided in this document is subject to legal disclaimers.
1.8 V dual UART with 128-byte FIFOs and IrDA encoder/decoder
Type
O
O
I
I
O
O
I
I
I
O
O
Rev. 4 — 1 February 2011
Description
When 16/68 pin is at logic 1 or unconnected, this output becomes
channel A interrupt output. The output state is defined by the user
through the software setting of MCR[3]. INTA is set to the active
mode and OP2A output to a logic 0 when MCR[3] is set to a
logic 1. INTA is set to the 3-state mode and OP2A is set to a logic 1
when MCR[3] is set to a logic 0.
When 16/68 pin is at logic 0, this output becomes device interrupt
output (active LOW, open-drain). An external pull-up resistor to
V
When 16/68 pin is at logic 1 or unconnected, this output becomes
channel B interrupt output. The output state is defined by the user
through the software setting of MCR[3]. INTB is set to the active
mode and OP2B output to a logic 0 when MCR[3] is set to a
logic 1. INTB is set to the 3-state mode and OP2B is set to a
logic 1 when MCR[3] is set to a logic 0.
When 16/68 pin is at logic 0, this output is not used.
When 16/68 pin is at logic 1, this input becomes the read strobe
(active LOW). When 16/68 pin is at logic 0, this input pin is not
used and should be connected to V
When 16/68 pin is at logic 1 or unconnected, this input becomes
the write strobe (active LOW).
When 16/68 pin is at logic 0, this input becomes read strobe when
it is at logic HIGH, and write strobe when it is at logic LOW.
Output 2 (user-defined). This function is associated with
individual channels, A through B. The state at these pin(s) are
defined by the user and through MCR register bit 3. INTA, INTB
are set to the active mode and OP2x to logic 0 when MCR[3] is set
to a logic 1. INTA, INTB are set to the 3-state mode and OP2x to a
logic 1 when MCR[3] is set to a logic 0 (see
Control Register bits
both the INTA, INTB operation and OP2x outputs, only one
function should be used at one time, INT or OP2.
Master Reset. When 16/68 pin is at logic 1 or unconnected, this
input becomes the RESET pin (active HIGH).
When 16/68 pin is at logic LOW, this input pin becomes RESET
(active LOW). (See
condition and software reset”
Ring Indicator (active LOW). These inputs are associated with
individual UART channels, A through B. A logic 0 on this pin
indicates the modem has received a ringing signal from the
telephone line. A logic 1 transition on this input pin will generate an
interrupt if modem status interrupt is enabled.
Request to Send (active LOW). These outputs are associated
with individual UART channels, A through B. A logic 0 on the RTSx
pin indicates the transmitter has data ready and waiting to send.
Writing a logic 1 in the modem control register MCR[1] will set this
pin to a logic 0, indicating data is available. After a reset this pin
will be set to a logic 1.
DD
is required.
Section 7.23 “SC16C852L external reset
description”, bit 3). Since these bits control
for initialization details.)
DD
.
SC16C852L
Table 21 “Modem
© NXP B.V. 2011. All rights reserved.
9 of 64