SC28L92A1B,557 NXP Semiconductors, SC28L92A1B,557 Datasheet - Page 35

• Manufacturer Part Number: SC28L92A1B,557
• Description: IC UART DUAL W/FIFO 44-PQFP
• Manufacturer: NXP Semiconductors
• Series: IMPACTr
• Type: Dual UARTr

Specifications of SC28L92A1B,557

• Number Of Channels: 2, DUART
• Package / Case: 44-MQFP, 44-PQFP
• Features: False-start Bit Detection
• Fifo's: 16 Byte
• Voltage - Supply: 3.3V, 5V
• With Auto Flow Control: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Data Rate: 0.2304 MBd
• Supply Voltage (max): 3.63 V or 5.5 V
• Supply Voltage (min): 2.97 V or 4.5 V
• Supply Current: 25 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 3.3 V or 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-1211; 935263294557; SC28L92A1B

NXP Semiconductors
SC28L92_7
Product data sheet
7.3.3.1 Command Register channel A (CRA)
7.3.3 Command registers
Table 38.
CRA is a register used to supply commands to channel A. Multiple commands can be
specified in a single write to CRA as long as the commands are non-conflicting, e.g., the
enable transmitter and reset transmitter commands cannot be specified in a single
command word.
Table 39.
Table 40.
Bit
7 to 4
3
2
1
0
Command
0000
0001
0010
0011
0100
0101
7
Symbol
-
-
-
-
-
channel command code
CRA - Command register channel A (address 0x2) and
CRB - Command register channel B (address 0xA) bit allocation
CRA - Command register channel A (address 0x2) bit description
Miscellaneous commands
Description
No command.
Reset MR pointer. Causes the channel A MR pointer to point to MR1.
Reset receiver. Resets the channel A receiver as if a hardware reset had been
applied. The receiver is disabled and the FIFO is flushed.
Reset transmitter. Resets the channel A transmitter as if a hardware reset had
been applied.
Reset error status. Clears the channel A received break, parity error, and overrun
error bits in the status register (SRA[7:4]). Used in character mode to clear OE
status (although RB, PE and FE bits will also be cleared) and in block mode to clear
all error status after a block of data has been received.
Reset channel A break change interrupt. Causes the channel A break detect
change bit in the interrupt status register (ISR[2]) to be cleared to zero.
6
Description
Miscellaneous commands. Execution of the commands in the upper four bits
of this register must be separated by 3 X1 clock edges. Other reads or writes
(including writes to the lower four bits) may be inserted to achieve this
separation. A description of miscellaneous commands is given in
Disable channel A transmitter. This command terminates transmitter operation
and reset the TxDRY and TxEMT status bits. However, if a character is being
transmitted or if a character is in the Tx FIFO when the transmitter is disabled,
the transmission of the character(s) is completed before assuming the inactive
state.
Enable channel A transmitter. Enables operation of the channel A transmitter.
The TxRDY and TxEMT status bits will be asserted if the transmitter is idle.
Disable channel A receiver. This command terminates operation of the
receiver immediately-a character being received will be lost. The command
has no effect on the receiver status bits or any other control registers. If the
special multi-drop mode is programmed, the receiver operates even if it is
disabled. See
Enable channel A receiver. Enables operation of the channel A receiver. If not
in the special wake-up mode, this also forces the receiver into the search for
start-bit state.
Rev. 07 — 19 December 2007
3.3 V/5.0 V Dual Universal Asynchronous Receiver/Transmitter
5
Section
4
6.3.10.
disable Tx
3
enable Tx
2
disable Rx
SC28L92
© NXP B.V. 2007. All rights reserved.
1
Table
enable Rx
35 of 73
0
40.