SC28L202A1DGG,118 NXP Semiconductors, SC28L202A1DGG,118 Datasheet - Page 47
![IC UART DUAL W/FIFO 56-TSSOP](/photos/6/90/69069/56-tssop_sml.jpg)
SC28L202A1DGG,118
Manufacturer Part Number
SC28L202A1DGG,118
Description
IC UART DUAL W/FIFO 56-TSSOP
Manufacturer
NXP Semiconductors
Series
IMPACTr
Datasheet
1.SC28L202A1DGG118.pdf
(77 pages)
Specifications of SC28L202A1DGG,118
Features
False-start Bit Detection
Number Of Channels
2, DUART
Fifo's
256 Byte
Voltage - Supply
3.3V, 5V
With Parallel Port
Yes
With Auto Flow Control
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Package / Case
56-TFSOP (0.240", 6.10mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
935276109118
SC28L202A1DGG-T
SC28L202A1DGG-T
SC28L202A1DGG-T
SC28L202A1DGG-T
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SC28L202A1DGG,118
Manufacturer:
EPCOS
Quantity:
12 000
Philips Semiconductors
REGISTER DESCRIPTIONS Mode Registers
MR0 Mode Register 0 MR0 is accessed by setting the MR pointer to 0 via the command register command B.
MR0[7] This bit controls the receiver watchdog timer. 0 = disable,
1 = enable. When enabled, the watch dog timer will generate a
receiver interrupt if the receiver FIFO has not been accessed within
64 bit times of the receiver 1X clock. This is used to alert the control
processor that data is in the RxFIFO that has not been read. This
situation may occur when the byte count of the last part of a
message is not large enough to generate an interrupt. This control
bit is duplicated WCXER(7:6)
MR0[6] – Bit 2 of receiver FIFO interrupt level. This bit along with Bit
6 of MR1 sets the fill level of the 8 byte FIFO that generates the
receiver interrupt.
MR0[6] MR1[6] Note that this control is split between MR0 and MR1.
This is for backward compatibility to the SC2692 and SCN2681.
Table 9. Receiver FIFO Interrupt Fill Level
Table 10. Receiver FIFO Interrupt Fill Level
For the receiver these bits control the number of FIFO positions
empty when the receiver will attempt to interrupt. After the reset the
receiver FIFO is empty. The default setting of these bits cause the
receiver to attempt to interrupt when it has one or more bytes in it.
2005 Nov 01
MR0 A
MR0 B
MR0 B[3:0]
are reserved
MR0[6] MR1[6]
00
01
10
11
MR0[6] MR1[6]
00
01
10
11
Dual UART
MR0[3] = 0
MR0[3] = 1
Bit 7
Rx WATCH
DOG
0 = Disable
1 = Enable
Interrupt Condition
1 or more bytes in FIFO (Rx RDY)
3 or more bytes in FIFO
6 or more bytes in FIFO
8 bytes in FIFO (Rx FULL)
Interrupt Condition
1 or more bytes in FIFO (Rx RDY)
128 or more bytes in FIFO
192 or more bytes in FIFO
256 bytes in FIFO (Rx FULL)
BIT 6
RxINT BIT 2
See Tables in
MR0 description
BIT (5:4)
TxINT (1:0)
See table #4
41
BIT 3
FIFO Size
0 = 8
1 = 256
MR0[5:4] – Tx interrupt fill level.
Table 11. Transmitter FIFO Interrupt Fill Level
Table 12. Transmitter FIFO Interrupt Fill Level
For the transmitter these bits control the number of FIFO positions
empty when the receiver will attempt to interrupt. After the reset the
transmit FIFO has 8 bytes empty. It will then attempt to interrupt as
soon as the transmitter is enabled. The default setting of the MR0
bits (00) condition the transmitter to attempt to interrupt only when it
is completely empty. As soon as one byte is loaded, it is no longer
empty and hence will withdraw its interrupt request.
MR0[3] – FIFO Size
MR0[2:0] – These bits are used to select one of the six–baud rate
groups.
See Table 13 for the group organization.
Other combinations of MR2[2:0] should not be used
NOTE: MR0[3:0] are not used in channel B and should be set to ‘0’.
MR0[5:4]
00
01
10
11
MR0[5:4]
00
01
10
11
000 Normal mode
001 Extended mode I
100 Extended mode II
MR0[3] = 0
MR0[3] = 1
BIT 2
BAUD RATE
EXTENDED II
0 = Norma
1 = Extend II
Interrupt Condition
8 bytes empty (Tx EMPTY)
4 or more bytes empty
6 or more bytes empty
1 or more bytes empty (Tx RDY)
Interrupt Condition
256 bytes empty (Tx EMPTY)
128 or more bytes empty
192 or more bytes empty
1 or more bytes empty (Tx RDY)
BIT 1
TEST 2
Set to 0
SC28L202
Product data sheet
BIT 0
BAUD RATE
EXTENDED 1
0 = Normal
1 = Extend