SC16C554DIB64,128 NXP Semiconductors, SC16C554DIB64,128 Datasheet - Page 32

• Manufacturer Part Number: SC16C554DIB64,128
• Description: IC UART QUAD SOT314-2
• Manufacturer: NXP Semiconductors

Specifications of SC16C554DIB64,128

• Number Of Channels: 4, QUART
• Fifo's: 16 Byte
• Voltage - Supply: 2.5V, 3.3V, 5V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Package / Case: 64-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935270063128; SC16C554DIB64-T; SC16C554DIB64-T

Philips Semiconductors
9397 750 13132
Product data
7.8 Modem Status Register (MSR)
Table 19:
This register provides the current state of the control interface signals from the
modem, or other peripheral device to which the SC16C554/554D is connected.
Four bits of this register are used to indicate the changed information. These bits are
set to a logic 1 whenever a control input from the modem changes state. These bits
are set to a logic 0 whenever the CPU reads this register.
Table 20:
Bit
0
Bit
7
6
5
4
3
2
Symbol
LSR[0]
Symbol
MSR[7]
MSR[6]
MSR[5]
MSR[4]
MSR[3]
MSR[2]
Line Status Register bits description
Modem Status Register bits description
Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder
Description
Receive data ready.
Description
CD (Active-HIGH, logical 1). Normally this bit is the complement of the
CD input. In the loop-back mode this bit is equivalent to the OP2 bit in the
MCR register.
RI (Active-HIGH, logical 1). Normally this bit is the complement of the RI
input. In the loop-back mode this bit is equivalent to the OP1 bit in the
MCR register.
DSR (Active-HIGH, logical 1). Normally this bit is the complement of the
DSR input. In loop-back mode this bit is equivalent to the DTR bit in the
MCR register.
CTS. CTS functions as hardware flow control signal input if it is enabled
via EFR[7]. The transmit holding register flow control is enabled/disabled
by MSR[4]. Flow control (when enabled) allows starting and stopping the
transmissions based on the external modem CTS signal. A logic 1 at the
CTS pin will stop SC16C554/554D transmissions as soon as current
character has finished transmission. Normally MSR[4] is the complement
of the CTS input. However, in the loop-back mode, this bit is equivalent to
the RTS bit in the MCR register.
Rev. 05 — 10 May 2004
CD
RI
Logic 0 = No data in receive holding register or FIFO (normal default
condition).
Logic 1 = Data has been received and is saved in the receive holding
register or FIFO.
Logic 0 = No CD change (normal default condition).
Logic 1 = The CD input to the SC16C554/554D has changed state
since the last time it was read. A modem Status Interrupt will be
generated.
Logic 0 = No RI change (normal default condition).
Logic 1 = The RI input to the SC16C554/554D has changed from a
logic 0 to a logic 1. A modem Status Interrupt will be generated.
[1]
[1]
…continued
SC16C554/554D
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
32 of 55