ATmega1284 Atmel Corporation, ATmega1284 Datasheet - Page 133

• Manufacturer Part Number: ATmega1284
• Manufacturer: Atmel Corporation

Specifications of ATmega1284

• Flash (kbytes): 128 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Eeprom (bytes): 4096
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8272C–AVR–06/11
Table 16-3 on page 133
the fast PWM mode.
Table 16-3.
Note:
Table 16-4 on page 133
the phase correct or the phase and frequency correct, PWM mode.
Table 16-4.
Note:
• Bit 1:0 – WGMn1:0: Waveform Generation Mode
Combined with the WGMn3:2 bits found in the TCCRnB Register, these bits control the counting
sequence of the counter, the source for maximum (TOP) counter value, and what type of wave-
form generation to be used, see
Timer/Counter unit are: Normal mode (counter), Clear Timer on Compare match (CTC) mode,
and three types of Pulse Width Modulation (PWM) modes.
COMnA1/COMnB1
COMnA1/COMnB1
1. A special case occurs when OCRnA/OCRnB equals TOP and COMnA1/COMnB1 is set. In
1. A special case occurs when OCRnA/OCRnB equals TOP and COMnA1/COMnB1 is set.
0
0
1
1
0
0
1
1
this case the compare match is ignored, but the set or clear is done at BOTTOM.
“16.9.3” on page 124
Section “16.9.4” on page 126
ATmega164A/PA/324A/PA/644A/PA/1284/P
Compare Output Mode, Fast PWM
Compare Output Mode, Phase Correct and Phase and Frequency Correct
PWM
(1)
shows the COMnx1:0 bit functionality when the WGMn3:0 bits are set to
shows the COMnx1:0 bit functionality when the WGMn3:0 bits are set to
COMnA0/COMnB0
COMnA0/COMnB0
for more details.
0
1
0
1
0
1
0
1
Table 16-5 on page
for more details.
Description
Normal port operation, OCnA/OCnB disconnected.
WGMn3:0 = 14 or 15: Toggle OC1A on Compare
Match, OC1B disconnected (normal port operation).
For all other WGM1 settings, normal port operation,
OC1A/OC1B disconnected.
Clear OCnA/OCnB on Compare Match, set
OCnA/OCnB at BOTTOM (non-inverting mode)
Set OCnA/OCnB on Compare Match, clear
OCnA/OCnB at BOTTOM (inverting mode)
Description
Normal port operation, OCnA/OCnB disconnected.
WGMn3:0 = 9 or 11: Toggle OCnA on Compare
Match, OCnB disconnected (normal port operation).
For all other WGM1 settings, normal port operation,
OC1A/OC1B disconnected.
Clear OCnA/OCnB on Compare Match when up-
counting. Set OCnA/OCnB on Compare Match when
downcounting.
Set OCnA/OCnB on Compare Match when up-
counting. Clear OCnA/OCnB on Compare Match
when downcounting.
(1)
134. Modes of operation supported by the
(See Section “16.9” on page
See Section
123).
See
133