ATmega8535 Atmel Corporation, ATmega8535 Datasheet - Page 219

• Manufacturer Part Number: ATmega8535
• Manufacturer: Atmel Corporation

Specifications of ATmega8535

• Flash (kbytes): 8 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

ADC Multiplexer Selection
Register – ADMUX
2502K–AVR–10/06
Table 83. Correlation Between Input Voltage and Output Codes
Example:
ADMUX = 0xED (ADC3 - ADC2, 10x gain, 2.56V reference, left adjusted result)
Voltage on ADC3 is 300 mV, voltage on ADC2 is 500 mV.
ADCR = 512 * 10 * (300 - 500)/2560 = -400 = 0x270
ADCL will thus read 0x00, and ADCH will read 0x9C. Writing zero to ADLAR right
adjusts the result: ADCL = 0x70, ADCH = 0x02.
• Bit 7:6 – REFS1:0: Reference Selection Bits
These bits select the voltage reference for the ADC, as shown in Table 84. If these bits
are changed during a conversion, the change will not go in effect until this conversion is
complete (ADIF in ADCSRA is set). The internal voltage reference options may not be
used if an external reference voltage is being applied to the AREF pin.
Table 84. Voltage Reference Selections for ADC
• Bit 5 – ADLAR: ADC Left Adjust Result
The ADLAR bit affects the presentation of the ADC conversion result in the ADC Data
Register. Write one to ADLAR to left adjust the result. Otherwise, the result is right
adjusted. Changing the ADLAR bit will affect the ADC Data Register immediately,
regardless of any ongoing conversions. For a complete description of this bit, see “The
ADC Data Register – ADCL and ADCH” on page 222.
Bit
Read/Write
Initial Value
V
V
V
...
V
V
V
...
V
V
REFS1
V
ADCn
ADCm
ADCm
ADCm
ADCm
ADCm
ADCm
ADCm
ADCm
0
0
1
1
+ (511/512) V
+ (510/512) V
+ (1/512) V
- (1/512) V
- (511/512) V
- V
+ V
REF
REF
REFS0
/GAIN
/GAIN
REFS1
0
1
0
1
R/W
7
0
REF
REF
REF
REF
REF
/GAIN
/GAIN
Voltage Reference Selection
AREF, Internal Vref turned off
AVCC with external capacitor at AREF pin
Reserved
Internal 2.56V Voltage Reference with external capacitor at AREF pin
/GAIN
REFS0
/GAIN
/GAIN
R/W
6
0
ADLAR
R/W
5
0
Read Code
0x1FE
0x1FF
0x1FF
0x3FF
0x001
0x000
0x201
0x200
MUX4
R/W
...
...
4
0
MUX3
R/W
3
0
Corresponding Decimal Value
MUX2
R/W
2
0
ATmega8535(L)
MUX1
R/W
1
0
-511
-512
511
511
510
-1
...
...
1
0
MUX0
R/W
0
0
ADMUX
219