ATxmega128B1 Atmel Corporation, ATxmega128B1 Datasheet - Page 12

• Manufacturer Part Number: ATxmega128B1
• Manufacturer: Atmel Corporation

Specifications of ATxmega128B1

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 53
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 8
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 10
• Input Capture Channels: 10
• Pwm Channels: 10
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

7. Memories
7.1
7.2
8330B–AVR–10/11
Features
Overview
•
•
•
•
The Atmel AVR architecture has two main memory spaces, the program memory and the data
memory. Executable code can reside only in the program memory, while data can be stored in
the program memory and the data memory. The data memory includes the internal SRAM, and
EEPROM for nonvolatile data storage. All memory spaces are linear and require no memory
bank switching. Nonvolatile memory (NVM) spaces can be locked for further write and read/write
operations. This prevents unrestricted access to the application software.
A separate memory section contains the fuse bytes. These are used for configuring important
system functions, and can only be written by an external programmer.
The available memory size configurations are shown in
addition, each device has a Flash memory signature row for calibration data, device identifica-
tion, serial number etc.
Flash program memory
Data memory
Production signature row memory for factory programmed data
User signature row
– One linear address space
– In-system programmable
– Self-programming and boot loader support
– Application section for application code
– Application table section for application code or data storage
– Boot section for application code or bootloader code
– Separate read/write protection lock bits for all sections
– Built in fast CRC check of a selectable flash program memory section
– One linear address space
– Single-cycle access from CPU
– SRAM
– EEPROM
– I/O memory
– Bus arbitration
– Separate buses for SRAM, EEPROM and I/O memory
– ID for each microcontroller device type
– Serial number for each device
– Calibration bytes for factory calibrated peripherals
– One flash page in size
– Can be read and written from software
– Content is kept after chip erase
Byte and page accessible
Optional memory mapping for direct load and store
Configuration and status registers for all peripherals and modules
4 bit-accessible general purpose registers for global variables or flags
Safe and deterministic handling of priority between CPU, DMA controller, and other bus
masters
Simultaneous bus access for CPU and DMA controller
”Ordering Information” on page
XMEGA B1
2. In
12