SAM7XC256 Atmel Corporation, SAM7XC256 Datasheet - Page 81
SAM7XC256
Manufacturer Part Number
SAM7XC256
Description
Manufacturer
Atmel Corporation
Specifications of SAM7XC256
Flash (kbytes)
256 Kbytes
Pin Count
100
Max. Operating Frequency
55 MHz
Cpu
ARM7TDMI
Hardware Qtouch Acquisition
No
Max I/o Pins
62
Ext Interrupts
62
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
2
Twi (i2c)
1
Uart
3
Can
1
Ssc
1
Ethernet
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
384
Resistive Touch Screen
No
Dac Resolution (bits)
No
Temp. Sensor
No
Crypto Engine
AES/DES
Sram (kbytes)
64
Self Program Memory
NO
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
3.3
Operating Voltage (vcc)
3.0 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- Current page: 81 of 284
- Download datasheet (2Mb)
3.4
3.4.1
3.4.2
3.4.3
ARM DDI 0029G
Addressing signals
A[31:0]
nRW
MAS[1:0]
The address class signals are:
•
•
•
•
•
•
•
A[31:0] is the 32-bit address bus that specifies the address for the transfer. All addresses
are byte addresses, so a burst of word accesses results in the address bus incrementing
by four for each cycle.
The address bus provides 4GB of linear addressing space.
When a word access is signaled the memory system ignores the bottom two bits, A[1:0],
and when a halfword access is signaled the memory system ignores the bottom bit,
A[0].
All data values must be aligned on their natural boundaries. All words must be
word-aligned.
nRW specifies the direction of the transfer. nRW indicates an ARM7TDMI processor
write cycle when HIGH, and an ARM7TDMI processor read cycle when LOW. A burst
of S-cycles is always either a read burst, or a write burst. The direction cannot be
changed in the middle of a burst.
The MAS[1:0] bus encodes the size of the transfer. The ARM7TDMI processor can
transfer word, halfword, and byte quantities.
All writable memory in an ARM7TDMI processor based system must support the
writing of individual bytes or halfwords to allow the use of the C Compiler and the
ARM debug tool chain, for example Multi-ICE.
A[31:0] on page 3-11
nRW on page 3-11
MAS[1:0] on page 3-11
nOPC on page 3-12
nTRANS on page 3-13
LOCK on page 3-13
TBIT on page 3-13.
Copyright © 1994-2001. All rights reserved.
Memory Interface
3-11
Related parts for SAM7XC256
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: