SAM9G20 Atmel Corporation, SAM9G20 Datasheet - Page 36
SAM9G20
Manufacturer Part Number
SAM9G20
Description
Manufacturer
Atmel Corporation
Datasheets
1.SAM9261.pdf
(248 pages)
2.SAM9261.pdf
(1274 pages)
3.SAM9261.pdf
(43 pages)
4.SAM9G20.pdf
(42 pages)
5.SAM9G20.pdf
(832 pages)
Specifications of SAM9G20
Flash (kbytes)
0 Kbytes
Pin Count
217
Max. Operating Frequency
400 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
96
Ext Interrupts
96
Usb Transceiver
3
Usb Speed
Full Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
1
Uart
7
Ssc
1
Ethernet
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
Yes
Adc Channels
4
Adc Resolution (bits)
10
Adc Speed (ksps)
95
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
32
Self Program Memory
NO
External Bus Interface
1
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
0.9 to 1.1
Fpu
No
Mpu / Mmu
No/Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
No
10.4.6
10.4.7
10.4.8
36
AT91SAM9G20 Summary
Multimedia Card Interface
USB Host Port
USB Device Port
Note:
• Each block contains two global registers that act on all three TC Channels
• One double-channel MultiMedia Card Interface
• Compatibility with MultiMedia Card Specification Version 3.11
• Compatibility with SD Memory Card Specification Version 1.1
• Compatibility with SDIO Specification Version V1.0.
• Card clock rate up to Master Clock divided by 2
• Embedded power management to slow down clock rate when not used
• MCI has two slots, each supporting
• Support for stream, block and multi-block data read and write
• Compliance with Open HCI Rev 1.0 Specification
• Compliance with USB V2.0 Full-speed and Low-speed Specification
• Supports both Low-Speed 1.5 Mbps and Full-speed 12 Mbps devices
• Root hub integrated with two downstream USB ports in the 217-LFBGA package
• Two embedded USB transceivers
• Supports power management
• Operates as a master on the Matrix
• USB V2.0 full-speed compliant, 12 MBits per second
• Embedded USB V2.0 full-speed transceiver
• Embedded 2,432-byte dual-port RAM for endpoints
• Suspend/Resume logic
• Ping-pong mode (two memory banks) for isochronous and bulk endpoints
• Six general-purpose endpoints
• Embedded pad pull-up
– Three external clock inputs
– Five internal clock inputs
– Two multi-purpose input/output signals
– One slot for one MultiMediaCard bus (up to 30 cards) or
– One SD Memory Card
– Endpoint 0 and 3: 64 bytes, no ping-pong mode
– Endpoint 1 and 2: 64 bytes, ping-pong mode
– Endpoint 4 and 5: 512 bytes, ping-pong mode
TC Block 0 (TC0, TC1, TC2) and TC Block 1 (TC3, TC4, TC5) have identical user interfaces. See
Figure 8-1, “AT91SAM9G20 Memory Mapping,” on page 19
addresses.
for TC Block 0 and TC Block 1 base
6384DS–ATARM–13-Jan-10