AT32UC3C1512C Automotive Atmel Corporation, AT32UC3C1512C Automotive Datasheet - Page 1149
AT32UC3C1512C Automotive
Manufacturer Part Number
AT32UC3C1512C Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.AT32UC3C0512C_AUTOMOTIVE.pdf
(1312 pages)
3.AT32UC3C0512C_AUTOMOTIVE.pdf
(107 pages)
- AT90CAN128_AUTOMOTIVE PDF datasheet
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #2
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #3
- Current page: 1149 of 1312
- Download datasheet (20Mb)
37.6
37.6.1
37.6.1.1
37.6.1.2
37.6.1.3
9166C–AVR-08/11
Functional Description
Basic Operation
Output channels
Timing constraints
Starting a conversion
The output from the DAC can either be continuous to one pin (DAC channel A only), or fed to
two different pins using a sample and hold circuitry (S/H). With S/H these two outputs can act
independently and create two different analog signals, different in both voltage and frequency.
The two S/H outputs have individual data and conversion control registers.
The DAC output may be used as internal input signal to other peripherals, such as the Analog
Comparator or the ADC. Only the DAC internal output can be used as internal input, the S/H out-
puts can not be used as such. Note that in this internal routing mode, both S/H modules must be
deactivated in order to avoid disturbances on the internal channel.
Some timing constraints must be observed in order to make sure the S/H circuitry operates cor-
rectly. These are relative to the frequency of the peripheral clock of the DACIFB, as this will
affect the charging/discharging periods of the S/H circuitry. Not meeting these constraints will
result in reducing the accuracy of the DAC conversions.
The DAC sampling time is the time interval between two conversions. Without S/H operating,
this figure should be equal or greater than the DAC minimum sampling period (corresponding to
the DAC maximum sampling frequency). With S/H operating, this figure should be equal or
greater than 1.5 times the DAC minimum sampling period.
When the sampling frequency is too low, the S/H circuitry may let the output voltage drop signif-
icantly between two consecutive conversions. If enabled, the auto-refresh mode will
automatically repeat continuously the conversion of the last channel data. This allows maintain-
ing the voltage level on the S/H outputs, whenever the time elapsed between two data to be
converted is too long. The DAC refresh time is the time interval between two channel data
updates, it can not be smaller than the minimum sampling period.
The analog DAC startup time is non-null, therefore a waiting period of a few CLK_DACIFB clock
cycles must be observed before considering conversion of the first data.
Note that if S/H is enabled, the actual sampling period will be 1.5 times greater than the pro-
grammed sampling period.
Conversions are either performed upon writes to the data registers or triggered by an incoming
event (auto-trig mode). Both application software and the Peripheral DMA controller may write to
the data registers.
Using the Peripheral DMA Controller to write data to the DACIFB, together with an event input to
trigger conversions, gives the most accurate timing for conversions.
The Peripheral DMA Controller data transfer rate depends on the sampling frequency imposed
by the event line. The DACIFB sends a request to the Peripheral DMA Controller, and once the
request is granted (Peripheral DMA Controller acknowledge) the conversion is performed upon
reception of a trigger event.
AT32UC3C
1149
Related parts for AT32UC3C1512C Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: