AT32UC3C1512C Automotive Atmel Corporation, AT32UC3C1512C Automotive Datasheet - Page 457
AT32UC3C1512C Automotive
Manufacturer Part Number
AT32UC3C1512C Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.AT32UC3C0512C_AUTOMOTIVE.pdf
(1312 pages)
3.AT32UC3C0512C_AUTOMOTIVE.pdf
(107 pages)
- AT90CAN128_AUTOMOTIVE PDF datasheet
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #2
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #3
- Current page: 457 of 1312
- Download datasheet (20Mb)
23.6.2.4
23.6.2.5
23.6.2.6
23.6.2.7
9166C–AVR-08/11
Pin Output Driver Control
Interrupts
Input Glitch Filter
Interrupt Timings
The GPIO has registers for controlling output drive properties of each pin, such as output driving
capability.
The driving capability is controlled by the Output Driving Capability Registers (ODCRn).
The GPIO can be configured to generate an interrupt when it detects a change on a GPIO pin.
Interrupts on a pin are enabled by writing a one to the corresponding bit in the Interrupt Enable
Register (IER). The module can be configured to generate an interrupt whenever a pin changes
value, or only on rising or falling edges. This is controlled by the Interrupt Mode Registers
(IMRn). Interrupts on a pin can be enabled regardless of the GPIO pin being controlled by the
GPIO or assigned to a peripheral function.
An interrupt can be generated on each GPIO pin. These interrupt generators are further grouped
into groups of eight and connected to the interrupt controller. An interrupt request from any of the
GPIO pin generators in the group will result in an interrupt request from that group to the inter-
rupt controller if the corresponding bit for the GPIO pin in the IER is set. By grouping interrupt
generators into groups of eight, four different interrupt handlers can be installed for each GPIO
port.
The Interrupt Flag Register (IFR) can be read by software to determine which pin(s) caused the
interrupt. The interrupt flag must be manually cleared by writing a zero to the corresponding bit
in IFR.
GPIO interrupts will only be generated when CLK_GPIO is enabled.
Input glitch filters can be enabled on each GPIO pin. When the glitch filter is enabled, a glitch
with duration of less than 1 CLK_GPIO cycle is automatically rejected, while a pulse with dura-
tion of 2 CLK_GPIO cycles or more is accepted. For pulse durations between 1 and 2
CLK_GPIO cycles, the pulse may or may not be taken into account, depending on the precise
timing of its occurrence. Thus for a pulse to be guaranteed visible it must exceed 2 CLK_GPIO
cycles, whereas for a glitch to be reliably filtered out, its duration must not exceed 1 CLK_GPIO
cycle. The filter introduces 2 clock cycles latency.
The glitch filters are controlled by the Glitch Filter Enable Register (GFER). When a bit in GFER
is one, the glitch filter on the corresponding pin is enabled. The glitch filter affects only interrupt
inputs. Inputs to peripherals or the value read through PVR are not affected by the glitch filters.
Figure 23-4
disabled. For the pulse to be registered, it must be sampled at the rising edge of the clock. In this
example, this is not the case for the first pulse. The second pulse is sampled on a rising edge
and will trigger an interrupt request.
shows the timing for rising edge (or pin-change) interrupts when the glitch filter is
AT32UC3C
457
Related parts for AT32UC3C1512C Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: