ST92250CV2Q-Auto STMicroelectronics, ST92250CV2Q-Auto Datasheet - Page 424
ST92250CV2Q-Auto
Manufacturer Part Number
ST92250CV2Q-Auto
Description
8-bit MCU for automotive
Manufacturer
STMicroelectronics
Datasheet
1.ST92150JDV1QAUTO.pdf
(430 pages)
Specifications of ST92250CV2Q-Auto
Internal Memory
Single Voltage FLASH up to 256 Kbytes, RAM up to 8Kbytes, 1K byte E3 TM (Emulated EEPROM)
Minimum Instruction Time
83 ns (24 MHz int. clock)
- Current page: 424 of 430
- Download datasheet (7Mb)
ST92124xxx-Auto/150xxxxx-Auto/250xxxx-Auto
KNOWN LIMITATIONS (Cont’d)
13.8 EMULATION CHIP LIMITATIONS
Additional limitations exist on Emulation chips (EMU2 emulator). These limitations correspond to those
present in AxxxxxxxxY trace codes (ST92F150). They are listed in the following table.
13.8.1
DIRECTIONAL, WEAK PULL-UP PORTS
This section applies to ports P1[7:3], P4[1], P8[7:2]
and P9[7:0].
During the reset phase (external reset signal low)
and the delay of 20400 clock periods (t
lowing a reset, these ports are in High Impedance
state, while according to the datasheet they should
Table 77. Reset Behaviour Table
Shaded areas represent erroneous operations.
424/430
1
Section 13.8.1
Section 13.8.2
Section 13.8.3
Section 13.8.4
Section 13.8.5
Section 13.8.6
Section 13.8.7
Section 13.8.8
Section 13.8.9
Section 13.8.10
Section 13.8.11
P1[7:3] Bi-Dir + WPU
P8[7:2] Bi-Dir + WPU
P9[7:0] Bi-Dir + WPU
Port
P4.1
Section
RESET
Bi-Dir + WPU
Datasheet
Condition
RESET BEHAVIOUR FOR BI-DIRECTIONAL, WEAK PULL-UP PORTS
HIGH DRIVE I/Os WHEN BSZ=1
ADC PARASITIC DIODE
ADC ACCURACY VS. NEGATIVE INJECTION CURRENT
I2CECCR REGISTER LIMITATION
I2C BEHAVIOUR DISTURBED DURING DMA TRANSACTIONS
MFT DMA MASK BIT RESET
DMA DATA CORRUPTED BY MFT INPUT CAPTURE
SCI-A WRONG BREAK DURATION
LIN MASTER MODE NOT PRESENT ON SCI-A
LIMITATIONS ON LQFP64 PACKAGES
BEHAVIOUR
While RESET
is low
Hi-Z
Hi-Z
Hi-Z
Hi-Z
FOR
RSPH
Port Behaviour
During next
Limitation (AxxxxxxxxY trace code)
20K Clock
) fol-
Cycles
BI-
Hi-Z
Hi-Z
Hi-Z
Hi-Z
have weak pull-ups. These ports then enter Weak
Pull-up state until the user overwrites the reset
values of I/O Port Control Registers PxC0, PxC1
and PxC2.
Rev Z Behaviour
Bi-Dir + WPU
Bi-Dir + WPU
Bi-Dir + WPU
Bi-Dir + WPU
After these
20K Clock
Cycles
PxC0
Control Register Value
0
0
0
0
PxC1
0
0
0
0
PxC2
0
0
0
0
Related parts for ST92250CV2Q-Auto
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: