ST92250CV2Q-Auto STMicroelectronics, ST92250CV2Q-Auto Datasheet - Page 60
ST92250CV2Q-Auto
Manufacturer Part Number
ST92250CV2Q-Auto
Description
8-bit MCU for automotive
Manufacturer
STMicroelectronics
Datasheet
1.ST92150JDV1QAUTO.pdf
(430 pages)
Specifications of ST92250CV2Q-Auto
Internal Memory
Single Voltage FLASH up to 256 Kbytes, RAM up to 8Kbytes, 1K byte E3 TM (Emulated EEPROM)
Minimum Instruction Time
83 ns (24 MHz int. clock)
- Current page: 60 of 430
- Download datasheet (7Mb)
ST92124xxx-Auto/150xxxxx-Auto/250xxxx-Auto
3.4 WRITE OPERATION EXAMPLE
Each operation (both Flash and
by a sequence of instructions like the following:
OR
LD
LD
..
LD
OR
The first instruction is used to select the desired
operation by setting its corresponding selection bit
in the Control Register (FCR for Flash operations,
ECR for
Table 11. Flash Write Operations
Table 12.
60/430
9
Sector Erase Suspend
FCR, #OPMASK ;Operation selection
ADD1, #DATA1 ;1st Add and Data
ADD2, #DATA2 ;2nd Add and Data
...., ......
ADDn, #DATAn ;nth Add and Data
FCR, #80h
Page Program
Set Protection
Byte Program
Page Update
Sector Erase
Chip Erase
Chip Erase
E
Operation
Operation
3 TM
E
3 TM
operations).
Write Operations
;n range = (1 to 16)
;Operation start
Selection bit
Selection bit
FPAGE
EPAGE
E
FBYTE
FSECT
FSUSP
FCHIP
ECHIP
PROT
3 TM
) is activated
Addresses and Data
Addresses and Data
From 1 to 4 sectors
From 1 to 16 bytes
From 1 to 16 bytes
From 1 to 4 bytes
The load instructions are used to set the address-
es (in the Flash or in the
the data to be modified.
The last instruction is used to start the write oper-
ation, by setting the start bit (FWMS for Flash op-
erations, EWMS for
register.
Once selected, but not yet started, one operation
can be cancelled by resetting the operation selec-
tion bit. Any latched address and data will be reset.
Warning: during the Flash Page Program or the
TM
the page address: only the last page address is ef-
fectively kept and all programming will effect only
that page.
A summary of the available Flash and
operations are shown in the following tables:
1 byte
None
None
None
Page Update operation it is forbidden to change
Start bit
Start bit
FWMS
FWMS
FWMS
FWMS
FWMS
EWMS
EWMS
None
E
3 TM
E
operation) in the Control
3 TM
memory space) and
Typical Duration
Typical Duration
160 µs (16 bytes)
1.5 s (1 sector)
40 µs (4 bytes)
30 ms
10 µs
15 µs
3 s
E
3 TM
write
E
3
Related parts for ST92250CV2Q-Auto
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: