MBM29LV160TE70TN Meet Spansion Inc., MBM29LV160TE70TN Datasheet - Page 19

• Manufacturer Part Number: MBM29LV160TE70TN
• Description: Flash Memory Cmos 16m 2m ? 8/1m ? 16 Bit
• Manufacturer: Meet Spansion Inc.

■ FUNCTIONAL DESCRIPTION
• Read Mode
The MBM29LV160TE/BE has two control functions which must be satisfied in order to obtain data at the outputs.
CE is the power control and should be used for a device selection. OE is the output control and should be used
to gate data to the output pins if a device is selected.
Address access time (t
access time (t
enable access time is the delay from the falling edge of OE to valid data at the output pins. (Assuming the
addresses have been stable for at least t
after power-up, it is necessary to input hardware reset or to change CE pin from “H” or “L”.
• Standby Mode
There are two ways to implement the standby mode on the MBM29LV160TE/BE devices. One is by using both
the CE and RESET pins; the other via the RESET pin only.
When using both pins, a CMOS standby mode is achieved with CE and RESET inputs both held at V
Under this condition the current consumed is less than 5 μA Max During Embedded Algorithm operation, V
Active current (I
either of these standby modes.
When using the RESET pin only, a CMOS standby mode is achieved with the RESET input held at V
(CE = “H” or “L”). Under this condition the current consumed is less than 5 μA Max Once the RESET pin is taken
high, the device requires t
In the standby mode, the outputs are in the high-impedance state, independent of the OE input.
• Automatic Sleep Mode
There is a function called automatic sleep mode to restrain power consumption during read-out of
MBM29LV160TE/BE data. This mode can be used effectively with an application requesting low power con-
sumption such as handy terminals.
To activate this mode, MBM29LV160TE/BE automatically switches itself to low power mode when addresses
remain stable for 150 ns. It is not necessary to control CE, WE, and OE in this mode. During such mode, the
current consumed is typically 1 μA (CMOS Level).
Standard address access timings provide new data when addresses are changed. While in sleep mode, output
data is latched and always available to the system.
• Output Disable
If the OE input is at a logic high level (V
be in a high-impedance state.
• Autoselect
The Autoselect mode allows the reading out of a binary code from the device and will identify its manufacturer
and type. The intent is to allow programming equipment to automatically match the device to be programmed
with its corresponding programming algorithm. The Autoselect command may also be used to check the status
of write-protected sectors. (See “MBM29LV160TE/BE Sector Protection Verify Autoselect Code” and “Expanded
Autoselect Code” Tables in “■FLEXIBLE SECTOR-ERASE ARCHITECTURE”.) This mode is functional over
the entire temperature range of the device.
To activate this mode, the programming equipment must force V
identifier bytes may then be sequenced from the devices outputs by toggling address A
addresses are DON’T CARES except A
The manufacturer and device codes may also be read via the command register, for instances when the
MBM29LV160TE/BE is erased or programmed in a system without access to high voltage on the A
(BYTE = V
IH
) or (BYTE = V
CE
) is the delay from stable addresses and stable CE to valid data at the output pins. The output
CC2
) is required even CE = “H”. The device can be read with standard access time (t
MBM29LV160TE
ACC
) is equal to the delay from stable addresses to valid output data. The chip enable
RH
IL
of wake up time before outputs are valid for read access.
)” Tables in “■DEVICE BUS OPERATIONS”) .
Retired Product DS05-20883-7E_July 31, 2007
IH
0
), output from the device is disabled. This will cause the output pins to
ACC
, A
1
- t
, and A
OE
time.) When reading out a data without changing addresses
6
(A
-1
). (See “MBM29LV160TE/BE User Bus Operation
70/90
ID
/MBM29LV160BE
(11.5 V to 12.5 V) on address pin A
0
from V
IL
9
CC
to V
SS
pin. The
CE
±0.3 V.
±0.3 V
70/90
) from
9
. Two
IH
. All
CC
19