P6002A Teccor Electronics, Inc., P6002A Datasheet - Page 156
P6002A
Manufacturer Part Number
P6002A
Description
solid state crowbar devices
Manufacturer
Teccor Electronics, Inc.
Datasheet
1.P6002A.pdf
(212 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
P6002AA
Manufacturer:
Littelfuse
Quantity:
45 000
Company:
Part Number:
P6002AA MCL
Manufacturer:
Littelfuse
Quantity:
45 000
Company:
Part Number:
P6002AAL
Manufacturer:
Littelfuse
Quantity:
45 000
Company:
Part Number:
P6002AB
Manufacturer:
Littelfuse
Quantity:
45 000
Company:
Part Number:
P6002AB MCL
Manufacturer:
Littelfuse
Quantity:
45 000
- Current page: 156 of 212
- Download datasheet (2Mb)
UL 497C
UL 497C
http://www.teccor.com
+1 972-580-7777
UL 497C requirements cover protectors for use on coaxial cable circuits. This standard
covers construction and performance requirements.
UL 497C Construction and Performance Requirements
The “Construction” section covers the following requirements:
• General
• Corrosion Protection
• Field-wiring Connections
• Components
• Spacing
• Enclosures
The “Performance” section covers the following requirements:
• General
• I
• Abnormal Sustained Current
• Component Temperature Test
• Breakdown Voltage Measurement
• Impulse Spark-over Voltage Measurement
• Limited Short-circuit Test
• High Current Ground Path Test
• Cable Shield Fuse Test
• Endurance Conditioning Test
• Induced Low Current Test
• Distortion Test
• Flame Test
• Impact Test (Polymeric Enclosures)
• Jarring Test
• Water Spray Test
• Leakage Current Test
• Dielectric Voltage-withstand Test
• Ultraviolet Light and Water Exposure
• Tensile Strength and Elongation Tests
• Air Oven Aging
• Ozone Exposure
Performance Requirements Specific to SIDACtor Devices
1. Strike Voltage Breakdown Test — Protectors are required to break down within ±25% of
2. Endurance Conditioning — Protectors are subjected to 500 impulse cycles. Each cycle is
the manufacturer’s specified breakdown range but no higher than 750 V at £ 2 kV/s rise
time.
a 1000 V peak, 10 A, 10x1000 µs pulse. Pulses are applied in one polarity at 10-second
intervals and then repeated in the opposite polarity. Then, 100 cycles of 1000 V peak,
100 A, 10x1000 µs pulse are applied to three new protectors. Finally, two cycles of
2
t Limiting
4 - 32
SIDACtor
®
Data Book and Design Guide
© 2002 Teccor Electronics
Related parts for P6002A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Power Rectifiers 15-20 Amp in TO-220AB Package
Manufacturer:
Teccor Electronics, Inc.
Part Number:
Description:
22A Iout, 600V Vrrm General Purpose Silicon Rectifier
Manufacturer:
Teccor Electronics, Inc.
Part Number:
Description:
275 V, four-port longitudinal two-chip protector
Manufacturer:
Teccor Electronics, Inc.
Datasheet:
Part Number:
Description:
SCRs 1-70 AMPS NON-SENSITIVE GATE
Manufacturer:
Teccor Electronics, Inc.
Datasheet:
Part Number:
Description:
400V V[drm] Max., 3.0A I[T] Max. Silicon Controlled Rectifier
Manufacturer:
Teccor Electronics, Inc.
Part Number:
Description:
Silicon COntrolled Rectifier 1-70 Amps
Manufacturer:
Teccor Electronics, Inc.
Part Number:
Description:
400V V[drm] Max., 4.0A I[T] Max. Silicon Controlled Rectifier
Manufacturer:
Teccor Electronics, Inc.
Part Number:
Description:
Sensitive SCR
Manufacturer:
Teccor Electronics, Inc.
Datasheet:
Part Number:
Description:
Thyristor Product Catalog
Manufacturer:
Teccor Electronics, Inc.
Datasheet:
Part Number:
Description:
Thyristor, 500V 0.8A IGT<500UA, Thyristor, high gate sensivity
Manufacturer:
Teccor Electronics, Inc.
Datasheet:
Part Number:
Description:
Thyristor, 500V 0.8A IGT<12UA, Thyristor, high gate sensivity
Manufacturer:
Teccor Electronics, Inc.
Datasheet:
Part Number:
Description:
Sensitive SCRs (0.8 - 10 Amps)
Manufacturer:
Teccor Electronics, Inc.
Datasheet: