MD3331-D64-V3 M-Systems Inc., MD3331-D64-V3 Datasheet - Page 17

no-image

MD3331-D64-V3

Manufacturer Part Number
MD3331-D64-V3
Description
Diskonchip Millennium Plus
Manufacturer
M-Systems Inc.
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MD3331-D64-V3
Manufacturer:
M-SYSTEMS
Quantity:
334
Part Number:
MD3331-D64-V3-X
Manufacturer:
SANDISK
Quantity:
18 135
Part Number:
MD3331-D64-V3-X
Manufacturer:
TI
Quantity:
699
Part Number:
MD3331-D64-V3-X
Quantity:
1 000
Part Number:
MD3331-D64-V3-X
Manufacturer:
M-SYSTEMS
Quantity:
20 000
Company:
Part Number:
MD3331-D64-V3-X
Quantity:
24
Company:
Part Number:
MD3331-D64-V3-X
Quantity:
1 545
2.3.3 Signal Descriptions
TSOP-I Package
DiskOnChip Millennium Plus 16MB TSOP-I and BGA packages support the identical signals in multiplexed
interface. The related pin and ball designations are listed in the signal descriptions, presented in logic groups, in
Table 3 and Table 4.
17
AD[15:0]
CE#
OE#
WE#
AVD#
ID0
LOCK#
BUSY#
IRQ#
RSTIN#
VCCQ
VCC
VSS
RSRVD
Signal
46-39, 35-28
5-11, 13-20,
25, 36, 48
Pin No.
12, 22
26
24
23
27
47
37
21
2
4
3
1
Table 3: Multiplexed Interface Signal Descriptions, TSOP-I Package
ST, R Chip Enable, active low.
Input
Type
OD
ST
ST
ST
ST
ST
ST
ST
-
-
-
-
-
Multiplexed bus. Address and data signals.
Output Enable, active low.
Write Enable, active low.
Sets multiplexed interface. Multiplexed mode is entered when a
rising edge is detected on this pin/ball.
Identification. For DiskOnChip Millennium Plus 16MB, up to two
chips can be cascaded in the same memory window, according to
the following assignment:
Chip 1 = ID0 = VSS; must be used for single chip configuration
Chip 2 = ID0 = VCC
Lock, active low. When active, provides full hardware data protection
of selected partitions.
Busy, active low, open drain. Indicates that DiskOnChip is initializing
and should not be accessed. A 10 K
even if the pin is not used.
Interrupt Request. Requires a 10 KΩ pull-up resistor.
Reset, active low.
I/O power supply. Requires a 10 nF and a 0.1 µF capacitor.
For 16MB devices, VCCQ may be either 2.7V to 3.6V or 1.65V to
1.95V.
For 32/64MB devices, VCCQ is 2.7V to 3.6V
Device supply. All VCC pins must be connected; each VCC pin
requires a 10 nF and 0.1 µF capacitor.
Ground. All VSS pins must be connected.
Reserved signal that is not connected internally and must be left
floating to guarantee forward compatibility with future products. It
should not be connected to arbitrary signals.
Data Sheet, Rev. 1.7
System Interface
Configuration
Reserved
Control
Power
Description
pull-up resistor is required
DiskOnChip Millennium Plus 16/32/64MByte
93-SR-002-03-8L
Signal
Supply
Supply
Supply
Output
Output
Output
Input/
Type
Input
Input
Input
Input
Input
Input
Input

Related parts for MD3331-D64-V3