T15C1 ACER, T15C1 Datasheet
T15C1
Related parts for T15C1
T15C1 Summary of contents
Page 1
... LCD MODULE SPECIFICATION Products Name:APAX T15C1 38.1CM(15.0 INCH) XGA(1024x768) 262K COLOR TFT LCD MODULE 5.0V l Preliminary Specification This technical specification is tentative and it will be changed without notice. Tel:02-87912868 Fax:02-87912869 進 金 生 實 業 股 份 有 限 公 司 台 北 市 內 湖 區 瑞 光 路 76 巷 39 號 4 樓 ...
Page 2
REVISION HISTORY 1. GENERAL DESCRIPTION 1.1 OVERVIEW 1.2 FEATURES 1.3 APPLICATION 1.4 GENERAL SPECIFICATIONS 1.5 MECHANICAL SPECIFICATIONS 2. ABSOLUTE MAXIMUM RATINGS 2.1 ABSOLUTE RATINGS OF ENVIRONMENT 2.2 ELECTRICAL ABSOLUTE RATINGS 2.2.1 TFT LCD MODULE 3. ELECTRICAL CHARACTERISTICS 3.1 TFT LCD ...
Page 3
Page Version Date (New) Ver 3.0 Dec.8’00 All REVISION HISTORY Section All Issue M150X1 approval spec Issued Date:Dec.8’2000 Model No.: M150X1 Approval Description Version 2.0 ...
Page 4
GENERAL DESCRIPTION 1.1 OVERVIEW M150X1 - 15.0” TFT Liquid Crystal Display module with 4 CCFL Backlight units and 60 pins TTL interface. This module supports 1024 x 768 XGA mode and can display 262,144 colors. The ...
Page 5
ABSOLUTE MAXIMUM RATINGS 2.1 ABSOLUTE RATINGS OF ENVIRONMENT Item Storage Temperature Operating Ambient Temperature Storage Humidity Operation Humidity Shock (Non-Operating) Vibration (Non-Operating) Note (1) Temperature and relative humidity range is shown in the figure below. (a) 85 %RH Max. ...
Page 6
ELECTRICAL ABSOLUTE RATINGS 2.2.1 TFT LCD MODULE Item Power Supply Voltage Logic Input Voltage Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal ...
Page 7
ELECTRICAL CHARACTERISTICS 3.1 TFT LCD MODULE Parameter Power Supply Voltage Ripple Voltage Rush Current Power Supply Current Differential Input Voltage for TTL Receiver Threshold Terminating Resistor Note (1) The module should be always operated within above ranges. Note (2) ...
Page 8
Note (3) The specified power supply current is under the conditions at Vcc = 5.0V ± 2 ºC, DC Current and Hz, whereas a power dissipation check pattern below is displayed White ...
Page 9
Note (2) The voltage shown above should be applied to the lamp for more than 1 second after startup. Otherwise the lamp may not be turned on. Note (3) The lamp frequency may generate interference with horizontal synchronous frequency from ...
Page 10
BLOCK DIAGRAM 4.1 TFT LCD MODULE Vcc LAMP CONNECTOR (JST-BHR-04VS-1) 4.2 BACKLIGHT UNIT TIMING CONTROLLER DC/DC CONVERTER & REFERENCE VOLTAGE GENERATOR Issued Date:Dec.8’2000 Model No.: M150X1 Approval TFT LCD PANEL (1024x3x768) DATA DRIVER IC BACKLIGHT UNIT ...
Page 11
INPUT TERMINAL PIN ASSIGNMENT 5.1 TFT LCD MODULE Pin No. Symbol I/O 1 GND ---- 2 RE0 I 3 RE1 I 4 RE2 I 5 RE3 I 6 RE4 I 7 RE5 I 8 GND ---- 9 GE0 I ...
Page 12
COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red, green and blue) is based on the 6-bit gray scale data input for the color. The higher the binary input the brighter the color. The table below provides ...
Page 13
INTERFACE TIMING 6.1 INPUT SIGNAL TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. Item Period Frequency Duty DCLK signal High time (Clock) Low time Rise time Fall time DCLK-Data Setup time ...
Page 14
DCLK ENAB RO5-0, RE5-0 GO5-0, GE5-0 BO5-0, BE5-0 RO5-0, RE5-0 GO5-0, GE5-0 BO5-0, BE5-0 ENAB RO5-0, RE5-0 GO5-0, GE5-0 BO5-0, BE5-0 ENAB DCLK RO5-0, RE5-0 GO5-0, GE5-0 BO5-0, BE5-0 ENAB INPUT SIGNAL TIMING DIAGRAM TclkH Tclk Tclkr ...
Page 15
Correspondence between Data and Display Position S0001 S0002 S0003 S0004 S0005 S0006 S0007 S0008 C001 0001 0001 0001 0002 C768 0001 0001 0001 0002 6.2 POWER ON/OFF SEQUENCE ON Vcc V 0.5 ...
Page 16
OPTICAL CHARACTERISTICS 7.1 TEST CONDITIONS Item Ambient Temperature Ambient Humidity Supply Voltage Input Signal Inverter Current The measurement methods of optical characteristics are shown in Section 7.2. The following items should be measured under the test conditions described in ...
Page 17
Note (1) Definition of Viewing Angle ( x, y): = 90º o’clock y- = 90º y- Note (2) Definition of Contrast Ratio (CR): The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = ...
Page 18
Note (4) Measurement Setup: The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 20 minutes ...
Page 19
PRECAUTIONS 8.1 HANDLING PRECAUTIONS (1) The module should be assembled into the system firmly by using every mounting hole. Be careful not to twist or bend the module. (2) While assembling or installing modules, it can only be in ...
Page 20
...
Page 21
...