MT9173AE Mitel Networks Corporation, MT9173AE Datasheet - Page 11

• Manufacturer Part Number: MT9173AE
• Description: Digital Subscriber Interface Circuit with RxSB
• Manufacturer: Mitel Networks Corporation

Preliminary Information
receiving signalling information and lower speed
data between the line and the system. In DN/DUAL
mode the DNIC receives a C-channel on CDSTi
while transmitting a C-channel on CDSTo.
channel times later (halfway through the frame) a D-
channel is received on CDSTi while a D-channel is
transmitted on CDSTo. This is shown in Figure 7.
The order of the C and D bytes in DUAL port mode
can be reversed by the mode select pins. See Table
1 for a listing of the byte orientations.
The D-channel exists only in DN mode and may be
used for transferring low speed data or signalling
information over the line at 8, 16 or 64 kbit/s (by
using the DINB feature). The information passes
transparently through the DNIC and is transmitted to
or received from the line at the bit rate selected in the
Control Register.
Notes:
Bit
0
1
2
3
4
5
6
7
Suggested use of ATTACK:
-At 160 kbit/s full convergence requires 850 ms with ATTACK held high for the first 240 frames or 30 ms.
-At 80 kbit/s full convergence requires 1.75 s with ATTACK held high for the first 480 frames or 60 ms.
When bits 4-7 of the Control Register are all set to one, the DNIC operates in one of the default modes as defined in Table 4a,
depending upon the status of bit-3.
Reg Sel-1
Reg Sel-1
Reg Sel-2
ATTACK
PSEN
TxHK
DINB
bit 0
Name
DRR
BRS
Reg Sel-2
bit 1
Register Select-1. Must be set to ’0’ to select the Control Register.
Register Select-2. Must be set to ’0’ to select the Control Register.
Diagnostics Register Reset. Writing a "0" to this bit will cause a diagnostics register reset
to occur coincident with the next frame pulse as in the MT8972A. When this bit is a logic
"1", the Diagnostics Register will not be reset.
Bit Rate Select. When set to ’0’ selects 80 kbit/s. When set to ’1’, selects 160 kbit/s.
D-Channel in B Timeslot. When ’0’, the D-channel bits (D0 or D0 and D1) corresponding
to the selected bit rate (80 or 160 kbit/s) are transmitted during the normal D-channel bit
times. When set to ’1’, the entire D-channel (D0-D7) is transmitted during the B1-channel
timeslot on the line providing a 64 kbit/s D-channel link.
Prescrambler/Deprescrambler Enable. When set to ’1’, the data prescrambler and
deprescrambler are enabled. When set to ’0’, the data prescrambler and deprescrambler
are disabled.
Convergence Speedup. When set to ’1’, the echo canceller will converge to the reflection
coefficient much faster. Used on power-up for fast convergence. When ’0’, the echo
canceller will require the normal amount of time to converge to a reflection coefficient.
Transmit Housekeeping. When set to ’0’, logic zero is transmitted over the line as
Housekeeping Bit. When set to ’1’, logic one is transmitted over the line as
Housekeeping Bit.
bit 2
DRR
Table 4. Control Register
F
bit 3
BRS
ifteen
DINB
bit 4
If the bit rate is 80 kbit/s, only D0 is transmitted and
received. At 160 kbit/s, D0 and D1 are transmitted
and received. When the DINB bit is set in the Control
Register the entire D-channel is transmitted and
received in the B1-channel timeslot.
The C-channel is used for transferring control and
status information between the DNIC and the
system. The Control and Diagnostics Registers are
accessed through the C-channel. They contain
information to control the DNIC and carry out the
diagnostics as well as the HK bit to be transmitted on
the line as described in Tables 4 and 5. Bits 0 and 1
of the C-channel select between the Control and
Diagnostics Register. If these bits are 0, 0 then the
C-channel information is written to the Control
Register (Table 4). If they are 0, 1 the C-
written to the Diagnostics Register (Table 5).
Default Mode Selection (Refer to Table 4a)
Description
PSEN
bit 5
ATTACK
bit 6
MT9173/74
TxHK
bit 7
c
hannel is
9-147