ISL6540A Intersil Corporation, ISL6540A Datasheet - Page 9

no-image

ISL6540A

Manufacturer Part Number
ISL6540A
Description
Single-Phase Buck PWM Controller
Manufacturer
Intersil Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL6540ACRZ
Manufacturer:
Intersil
Quantity:
35
Part Number:
ISL6540ACRZ
Manufacturer:
ISL
Quantity:
20 000
Part Number:
ISL6540AIRZ
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ISL6540AIRZA
Manufacturer:
Intersil
Quantity:
20
Electrical Specifications
Functional Pin Description
VSEN+ (Pin 1)
This pin provides differential remote sense for the ISL6540A.
It is the positive input of a standard instrumentation amplifier
topology with unity gain, and should connect to the positive
rail of the load/processor. The voltage at this pin should be
set equal to the internal system reference voltage (0.591V
typical.)
VSEN- (Pin 2)
This pin provides differential remote sense for the regulator.
It is the negative input of the instrumentation amplifier, and
should connect to the negative rail of the load/processor.
Typically 6μA is sourced from this pin. The output of the
remote sense buffer is disabled (High Impedance) by pulling
VSEN- to VCC.
REFOUT (Pin 3)
This pin connects to the unmargined system reference
through an internal buffer. It has a 19mA drive capability with
an output common mode range of GND to VCC. The
REFOUT buffer requires at least 1μF of capacitive loading to
be stable. This pin should not be left floating.
REFIN (Pin 4)
When the external reference pin (REFIN) is NOT within
~1.8V of VCC, the REFIN pin is used as the system
reference instead of the internal 0.591V reference. The
recommended REFIN input voltage range is ~68mV to
VCC - 1.8V.
SS (Pin 5)
This pin provides softstart functionality for the ISL6540A. A
capacitor connected to ground along with the internal 37µA
Operational Transconductance Amplifier (OTA), sets the
soft-start interval of the converter. This pin is directly
connected to the non-inverting input of the error amplifier. To
prevent noise injection into the error amplifier the SS
capacitor should be located next to the SS and GND pins.
OFS+ (Pin 6)
This pin sets the positive margining offset voltage. Resistors
should be connected to GND (R
from this pin. With MAR_CTRL logic low, the internal 0.591V
reference is developed at the OFS+ pin across resistor
R
R
and OFS- is divided by 5 and imposed on the system
reference. The maximum designed offset of 1V between
OFS+ and OFS- pins translates to a 200mV offset.
OFS+
MARG
SYMBOL
V
I
I
PG_LOW
PG_MAX
PG_MAX
. The voltage on OFS+ is driven from OFS- through
. The resulting voltage differential between OFS+
PGOOD Low Output Voltage
Maximum Sinking Current
Maximum Open Drain Voltage
PARAMETER
9
Recommended Operating Conditions, Unless Otherwise Noted (Continued)
OFS+
) and OFS- (R
I
V
VCC = 3.3V
PGOOD
PGOOD
MARG
= 5mA
= 0.8V
)
ISL6540A
TEST CONDITIONS
OFS- (Pin 7)
This pin sets the negative margining offset voltage. Resistors
should be connected to GND (R
from this pin. With MAR_CTRL logic low, the internal 0.591V
reference is developed at the OFS- pin across resistor
R
R
and OFS- is divided by 5 and imposed on the system
reference. The maximum designed offset of -1V between
OFS+ and OFS- pins translates to a -200mV offset of the
system reference.
VCC (Pin 8, Analog Circuit Bias)
This pin provides power for the ISL6540A analog circuitry.
The pin should be connected to a 2.9V to 5.5V bias through
an RC filter from PVCC to prevent noise injection into the
analog circuitry. This pin can be powered off the internal or
external linear regulator options.
MARCTRL (Pin 9)
The MARCTRL pin controls margining function, a logic high
enables positive margining, a logic low sets negative
margining, a high impedance disables margining.
PG_DLY (Pin 10)
Provides the ability to delay the output of the PGOOD
assertion by connecting a capacitor from this pin to GND. A
0.1
PGOOD (Pin 11)
Provides an open drain Power Good signal when the output
is within 9% of nominal output regulation point with 6%
hysteresis (15%/9%), and after soft-start is complete.
PGOOD monitors the VMON pin.
EN (Pin 12)
This pin is compared with an internal 0.50V reference and
enables the soft-start cycle. This pin also can be used for
voltage monitoring. A 10μA current source to GND is active
while the part is disabled, and is inactive when the part is
enabled. This provides functionality for programmable
hysteresis when the EN pin is used for voltage monitoring.
VFF (Pin 13)
The voltage at this pin is used for input voltage feed forward
compensation and sets the internal oscillator ramp peak to
peak amplitude at 0.16 * VFF. An external RC filter may be
required at this pin in noisy input environments. The
minimum recommended VFF voltage is 2.97V.
OFS-
MARG
μ
F capacitor produces approximately a 7ms delay.
. The voltage on OFS- is driven from OFS+ through
. The resulting voltage differential between OFS+
MIN
23
-
-
OFS-
TYP
6
-
-
) and OFS+ (R
0.150
MAX
-
-
March 12, 2007
MARG
UNITS
FN6288.2
mA
V
V
)

Related parts for ISL6540A