LM3S1439 Luminary Micro, Inc, LM3S1439 Datasheet - Page 63
![no-image](/images/no-image-200.jpg)
LM3S1439
Manufacturer Part Number
LM3S1439
Description
Lm3s1439 Arm Microcontroller
Manufacturer
Luminary Micro, Inc
Datasheet
1.LM3S1439.pdf
(544 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM3S1439-EQC50-A2
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S1439-EQC50-A2T
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S1439-IBZ50-A2
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S1439-IBZ50-A2T
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S1439-IQC50-A2
Manufacturer:
Texas Instruments
Quantity:
135
Company:
Part Number:
LM3S1439-IQC50-A2T
Manufacturer:
Texas Instruments
Quantity:
10 000
- Current page: 63 of 544
- Download datasheet (6Mb)
6.1.2.6
6.1.2.7
July 25, 2008
Brown-out resets are controlled with the Power-On and Brown-Out Reset Control (PBORCTL)
register. The BORIOR bit in the PBORCTL register must be set for a brown-out condition to trigger
a reset.
The brown-out reset is equivelent to an assertion of the external RST input and the reset is held
active until the proper V
handler to determine if a Brown-Out condition was the cause of the reset, thus allowing software to
determine what actions are required to recover.
The internal Brown-Out Reset timing is shown in Figure 22-12 on page 515.
Software Reset
Software can reset a specific peripheral or generate a reset to the entire system .
Peripherals can be individually reset by software via three registers that control reset signals to each
peripheral (see the SRCRn registers). If the bit position corresponding to a peripheral is set and
subsequently cleared, the peripheral is reset. The encoding of the reset registers is consistent with
the encoding of the clock gating control for peripherals and on-chip functions (see “System
Control” on page 67). Note that all reset signals for all clocks of the specified unit are asserted as
a result of a software-initiated reset.
The entire system can be reset by software by setting the SYSRESETREQ bit in the Cortex-M3
Application Interrupt and Reset Control register resets the entire system including the core. The
software-initiated system reset sequence is as follows:
1.
2.
3.
The software-initiated system reset timing is shown in Figure 22-13 on page 515.
Watchdog Timer Reset
The watchdog timer module's function is to prevent system hangs. The watchdog timer can be
configured to generate an interrupt to the controller on its first time-out, and to generate a reset
signal on its second time-out.
After the first time-out event, the 32-bit counter is reloaded with the value of the Watchdog Timer
Load (WDTLOAD) register, and the timer resumes counting down from that value. If the timer counts
down to its zero state again before the first time-out interrupt is cleared, and the reset signal has
been enabled, the watchdog timer asserts its reset signal to the system. The watchdog timer reset
sequence is as follows:
1.
2.
3.
A software system reset is initiated by writing the SYSRESETREQ bit in the ARM Cortex-M3
Application Interrupt and Reset Control register.
An internal reset is asserted.
The internal reset is deasserted and the controller loads from memory the initial stack pointer,
the initial program counter, and the first instruction designated by the program counter, and
then begins execution.
The watchdog timer times out for the second time without being serviced.
An internal reset is asserted.
The internal reset is released and the controller loads from memory the initial stack pointer, the
initial program counter, the first instruction designated by the program counter, and begins
execution.
DD
level is restored. The RESC register can be examined in the reset interrupt
Preliminary
LM3S1439 Microcontroller
63
Related parts for LM3S1439
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LM3-100K-TR](/images/no-image3.png)
Part Number:
Description:
Inductor: Molded: 10u: 10%: 30M: 7.9: 440m: Axial: T/R
Manufacturer:
Inductor Supply, Inc.
![LM3-R15](/images/no-image3.png)
Part Number:
Description:
Molded Inductor
Manufacturer:
Inductor Supply, Inc.
Datasheet:
![LM3-PWN1-01-N1](/images/no-image3.png)
Part Number:
Description:
Cree Smd Led
Manufacturer:
Cree, Inc.
Datasheet:
![LM3-PBL1-01-N1](/images/no-image3.png)
Part Number:
Description:
Cree Smd Led
Manufacturer:
Cree, Inc.
Datasheet:
![LM3-EWN1-01-N1-MT](/images/no-image3.png)
Part Number:
Description:
Specification For Cotco Led Lamp
Manufacturer:
Marktech Optoelectronics
Datasheet:
![LM3S1110](/images/no-image3.png)
Part Number:
Description:
Lm3s1110 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1133](/images/no-image3.png)
Part Number:
Description:
Lm3s1133 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1138](/images/no-image3.png)
Part Number:
Description:
Lm3s1138 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1150](/images/no-image3.png)
Part Number:
Description:
Lm3s1150 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1162](/images/no-image3.png)
Part Number:
Description:
Lm3s1162 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1165](/images/no-image3.png)
Part Number:
Description:
Lm3s1165 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1332](/images/no-image3.png)
Part Number:
Description:
Lm3s1332 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1435](/images/no-image3.png)
Part Number:
Description:
Lm3s1435 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet: