ds3171n Maxim Integrated Products, Inc., ds3171n Datasheet - Page 72
ds3171n
Manufacturer Part Number
ds3171n
Description
Ds3171, Ds3172, Ds3173, Ds3174 Single/dual/triple/quad Ds3/e3 Single-chip Transceivers
Manufacturer
Maxim Integrated Products, Inc.
Datasheet
1.DS3171N.pdf
(234 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 72 of 234
- Download datasheet (2Mb)
DS3171/DS3172/DS3173/DS3174
be framing errors if a framed mode is enabled. When the DS3 framed AIS signal is initiated or terminated, in
addition to no BPV or CV errors, there should be no framing or P-bit (parity) or CP-bit errors introduced.
The AIS signal generated at the top level will not generate BPV errors but may generate P-bit and CP-bit errors
when the signal is initiated and terminated. The framed DS3 AIS signal will not cause the far end receiver to re-
sync when the signal is initiated, but it may cause a re-sync when terminated if the DS3 frame position in the
framer is changed while the DS3 AIS signal is being generated. A sequence of events can be executed which will
enable the initiation and termination of DS3 AIS or unframed all ones at the top level without any errors introduced.
The sequence will only work when the automatic AIS generation is not enabled. CV and P-bit errors can occur
when AIS is automatically generated and cannot be avoided. This sequence to generate an error free DS# AIS at
the top level is to have the DS3 AIS or unframed all ones signal initiate in the DS3 framer, and a few frames sent
before initiating or terminating the DS3 AIS or unframed all ones at the top level. After the top level AIS signal is
activated, the AIS signal in the framer can be terminated, DLB activated and diagnostic patterns generated. The
DS3 AIS signal generated at the top level will not change frame alignment after starting even if the DS3 frame
position in the framer is changed.
The transmit line AIS generator at the top level can generate AIS signals even when the framer is looped back
using DLB, but not when the line is looped back using LLB. The AIS signal generated in the framer will be looped
back to the receive side when DLB is activated.
The receive framer can detect both unframed all ones AIS and DS3 framed AIS patterns. When in DS3 framing
modes, both framed DS3 AIS and unframed all ones can be detected. In E3 framing modes E3 AIS, which is
unframed all ones, is detected.
The receive payload interface going to the RSERn pin or the BERT logic can have an unframed all ones AIS signal
replacing the receive signal, this is called Payload AIS. The all ones AIS signal is generated from either the DS3/E3
framer or the downstream top level unframed all ones AIS generator. The unframed all ones AIS signal generated
in the framer will be looped back to the transmit side when PLB is activated. The unframed all ones AIS signal
generated at the top level will be sent to the RSERn pin and other receive logic, but not to the transmit side while
PLB is activated. The top level AIS generator is used when a downstream AIS signal is desired while payload loop
back is activated and is enabled by default after rest and must be cleared during configuration. Note that the
downstream AIS circuit in the framer, when a DS3 mode is selected, enforces the OOF to be active for 2.5 ms
before activating when automatic AIS in the framer is enabled. The top level downstream AIS will be generated
with no delay when OOF is detected when automatic AIS at the top level is enabled.
There is no detection of any AIS signal on the transmit payload signal from the TSERn pin or anywhere on the
transmit data path.
The transmit AIS generator at the top level can also be activated with a software bit or automatically when DLB is
activated. The receive AIS generator in the framer can be activated with a software bit, and automatically when
AIS, LOS or OOF are detected. The receive payload AIS generator at the top level can be activated with a software
bit or automatically when LOS, DS3/E3 OOF, LLB or PLB is activated.
72
Related parts for ds3171n
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Nonvolatile Ram Controller Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
3.3v Single-piece 8mb Nonvolatile Sram Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Pon Triplexer Control And Monitoring Circuit Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Ttl Compatible Cmos Analog Switches Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Improved Low-power, Cmos Analog Switches With Latches Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Windows Vista-compliant, Stereo Class Ab Speaker Amplifiers And Directdrive Headphone Amplifiers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
4a, 20ns, Dual Mosfet Drivers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Nicd/nimh Battery Fast-charge Controllers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
3.6v, 1w Autoramping Power Amplifier For 900mhz Applications Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
2.7v, Single-supply, Cellular-band Linear Power Amplifiers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
5ghz Linear Power Amplifiers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Evaluation Kits for the MAX3514
Manufacturer:
Maxim Integrated Products, Inc.
Part Number:
Description:
5v, Differential Input, Directdrive, 130mw Stereo Headphone Amplifiers With Shutdown Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Accurate I2c Rtc With Integrated Tcxo/crystal/fram
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Ds1863 Burst-mode Pon Controller With Integrated Monitoring
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet: