cs4297 Cirrus Logic, Inc., cs4297 Datasheet - Page 34
cs4297
Manufacturer Part Number
cs4297
Description
Crystalclear Soundfusion Audio Codec 97 Logic
Manufacturer
Cirrus Logic, Inc.
Datasheet
1.CS4297.pdf
(46 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
cs4297-JQ
Manufacturer:
CRYSTALCI
Quantity:
326
Company:
Part Number:
cs4297-JQ
Manufacturer:
CRYSTAL
Quantity:
850
Part Number:
cs4297-JQ
Manufacturer:
CS
Quantity:
20 000
Company:
Part Number:
cs4297A-JQ
Manufacturer:
CIRRUS
Quantity:
560
Company:
Part Number:
cs4297A-JQ
Manufacturer:
CRYSTAL
Quantity:
624
Part Number:
cs4297A-JQ
Manufacturer:
CS
Quantity:
20 000
Part Number:
cs4297A-JQ-EP
Manufacturer:
N/A
Quantity:
20 000
Part Number:
cs4297A-JQEP
Manufacturer:
CRYSTAL
Quantity:
20 000
Company:
Part Number:
cs4297AJQR
Manufacturer:
HIT
Quantity:
6 951
PERFORMANCE PLOTS
Figures 11 through 26 show the overall Frequency
Response, the THD+N over frequency, and the DR
over frequency of the ADCs, the DACs, the analog
mixer (Line In to Line Out) and the microphone in-
puts. Crosstalk plots and the noise floor FFT plots
of the DACs, the analog mixer and the muted noise
floor of the CS4297 are also included. All plots
were taken on a CRD4297-1 with a CS4297-KQ
Codec.
Figures 11, 14, 17, and 20: The Frequency Re-
sponse plots were taken using a -20 dB FS input
signal swept over the frequency range of 20 Hz to
20 kHz and normalized to 0 dB at 1 kHz.
Figures 12, 15, 18, and 21: The THD+N plots were
taken using a -3 dB FS input signal swept over the
frequency range of 20 Hz to 20 kHz. These perfor-
mance plots used an “A”-weighted filter applied on
the output with the exception of the ADC THD+N
plot.
Figures 13, 16, 19, and 22: The Dynamic Range
plots were taken using a -50 dB FS input signal
swept over the frequency range of 20 Hz to 20 kHz.
These performance plots used an “A”-weighted fil-
ter applied on the output with the exception of the
ADC Dynamic Range plot.
Figure 23: The crosstalk plot was generated using a
0 dB FS input signal on one channel of the
LINE_IN input and measuring the magnitude of
the other output channel swept over the frequency
34
range of 20 Hz to 20 kHz. This performance plots
used an “A”-weighted filter applied on the output
Figures 24, 25, and 26: The noise floor plots were
generated by running a 16K-point FFT on the
LINE_OUT output with no input signal applied.
The Muted Noise Floor plot was taken with the
master mute bit ‘set’ (bit D15, register 0x02h).
These performance plots used an “A”-weighted fil-
ter applied on the output
All audio performance plots used unity gain set-
tings on the analog volume controls. Additionally,
the microphone input plots were taken with the +20
dB gain stage enabled (bit D6, register 0x0Eh).
The ADC plots used the A-D signal path. The DAC
plots used the D-A signal path. The mixer and the
microphone plots used the A-A signal path.
CrystalClear™ SoundFusion™ Audio Codec ’97
CS4297
DS242F5