mpc5554mzp80r2 Freescale Semiconductor, Inc, mpc5554mzp80r2 Datasheet - Page 5

• Manufacturer Part Number: mpc5554mzp80r2
• Description: Mpc5554 High Performance Microcontroller
• Manufacturer: Freescale Semiconductor, Inc

1
2
3
4
5
6
7
8
9
10
11
12
3.2
The shaded rows in the following table indicate information specific to a four-layer board.
Freescale Semiconductor
1
2
3
4
Spec
Spec
28
29
Functional operating conditions are given in the DC electrical specifications. Absolute maximum ratings are stress ratings only,
and functional operation at the maxima is not guaranteed. Stress beyond any of the listed maxima can affect device reliability
or cause permanent damage to the device.
1.5 V ± 10% for proper operation. This parameter is specified at a maximum junction temperature of 150
All functional non-supply I/O pins are clamped to V
AC signal overshoot and undershoot of up to ± 2.0 V of the input voltages is permitted for an accumulative duration of
60 hours over the complete lifetime of the device (injection current not limited for this duration).
Internal structures hold the voltage greater than –1.0 V if the injection current limit of 2 mA is met. Keep the negative DC
voltage greater than –0.6 V on eTPUB[15] and SINB during the internal power-on reset (POR) state.
Internal structures hold the input voltage less than the maximum voltage on all pads powered by V
maximum injection current specification is met (2 mA for all pins) and V
Internal structures hold the input voltage less than the maximum voltage on all pads powered by V
injection current specification is met (2 mA for all pins) and V
Total injection current for all pins (including both digital and analog) must not exceed 25 mA.
Total injection current for all analog input pins must not exceed 15 mA.
Lifetime operation at these specification limits is not guaranteed.
Moisture sensitivity profile per IPC/JEDEC J-STD-020D.
Moisture sensitivity per JEDEC test method A112.
Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board)
temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal
resistance.
Per SEMI G38-87 and JEDEC JESD51-2 with the single-layer board horizontal.
Per JEDEC JESD51-6 with the board horizontal.
Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on
the top surface of the board near the package.
1
2
3
4
5
6
7
Maximum solder temperature
Moisture sensitivity level
Junction to ambient
Junction to ambient
Junction to ambient
Junction to ambient
Junction to board
Junction to case
Junction to package top
Lead free (PbFree)
Leaded (SnPb)
Thermal Characteristics
5
4
(four-layer board 2s2p)
1, 2
1, 3
1, 3
1, 3
MPC5554 Thermal Characteristic
Characteristic
12
, natural convection (one-layer board)
, natural convection (four-layer board 2s2p)
Table 2. Absolute Maximum Ratings
(@200 ft./min., one-layer board)
(@200 ft./min., four-layer board 2s2p)
6
, natural convection
11
Table 3. MPC5554 Thermal Characteristics
MPC5554 Microcontroller Data Sheet, Rev. 2.0
SS
and V
DDE
DDE
, or V
is within the operating voltage specifications.
DDEH
DDEH
Symbol
.
1
T
MSL
SDR
(continued)
is within the operating voltage specifications.
Symbol
R
R
R
R
R
R
Ψ
θJMA
θJMA
θJC
θJA
θJA
θJB
JT
Min
—
—
DDE
Electrical Characteristics
DDEH
supplies, if the maximum
416
supplies, if the
24
18
19
15
o
PBGA
9
5
2
260.0
245.0
C.
Max
3
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
Unit
Unit
o
C
5