ata6603 ATMEL Corporation, ata6603 Datasheet - Page 6

no-image

ata6603

Manufacturer Part Number
ata6603
Description
Microcontroller With Lin Transceiver, 5v Regulator And Watchdog
Manufacturer
ATMEL Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ata6603-PLQW
Manufacturer:
JTEC
Quantity:
2
Part Number:
ata6603P
Quantity:
1 262
Part Number:
ata6603P-PLQW
Manufacturer:
ATMEL
Quantity:
2 000
Part Number:
ata6603P-PLQW
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ata6603PPLQW
Manufacturer:
STM
Quantity:
5 006
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.3.6
6
Functional Description
ATA6602/ATA6603
Supply Pin (VS)
Ground Pin (GND)
Undervoltage Reset Output (NRES)
Voltage Regulator Output Pin (VDD)
Voltage Regulator Sense Pin (PVDD)
Bus Pin (LIN)
The LIN operating voltage is V
able transmission if V
NRES switches to low and the IC enters Pre-normal mode. After switching on VS, the IC starts
with the Pre-normal mode and the voltage regulator is switched on (that is, 5V/50 mA output
capability).
The supply current in Sleep mode is typically 10 µA, and 40 µA in Silent mode.
The IC is neutral on the LIN pin in case of GND disconnection; it can handle a ground shift up to
3V for supply voltage at the VS pin above 9V.
This push-pull output is supplied from the V
voltage detection threshold of V
except the IC is switched into Sleep mode. Even if V
internally driven from the V
then becomes highly resistant.
The implemented undervoltage delay keeps NRES low for t
normal value.
The internal 5V voltage regulator is capable of driving loads with up to 50 mA of current con-
sumption; it is able to supply the microcontroller and other ICs on the PCB. It is protected
against overloads by means of current limitation and overtemperature shutdown. Furthermore,
the output voltage is monitored and will cause a reset signal at the NRES output pin if the output
voltage drops below a defined threshold V
nal NPN transistor may be used with its base connected to the VDD pin and its emitter
connected to PVDD.
This is the sense input pin of the 5V voltage regulator. For normal applications (that is, when
only using the internal output transistor), this pin is connected to the VDD pin. If an external
boosting transistor is used, the PVDD pin must be connected to the output of this transistor, its
emitter terminal.
A low side driver with internal current limitation and thermal shutdown, and an internal pull-up
resistor in compliance with LIN specification 2.0 is implemented. This is a self-adapting current
limitation; that is, during current limitation, as the chip temperature increases, the current
decreases. The allowed voltage range is between –40V and +60V. Reverse currents from the
LIN bus to VS are suppressed, even in case of ground shifts or battery disconnection. LIN
receiver thresholds are compatible to the LIN protocol specification. The fall time from recessive
bus state to dominant, and the rise time from dominant bus state to recessive are slope
controlled.
S
falls below 5V in order to avoid false bus messages. In this case the
S
voltage. If V
S
= 5V to 18V. An undervoltage detection is implemented to dis-
thun
, NRES switches to low after t
S
thun
voltage ramps down, NRES stays until V
CC
. To boost up the maximum load current, an exter-
voltage. If the V
CC
= 0V the NRES stays low, because it is
Reset
CC
= 10 ms after V
voltage falls below the under-
res_f
(Figure 3-8 on page
4921D–AUTO–08/07
CC
S
reaches its
< 1.5V and
15)

Related parts for ata6603