clc1605 Cadeka Microcircuits LLC., clc1605 Datasheet - Page 14
![no-image](/images/no-image-200.jpg)
clc1605
Manufacturer Part Number
clc1605
Description
Single And Triple, 1.5ghz Amplifers
Manufacturer
Cadeka Microcircuits LLC.
Datasheet
1.CLC1605.pdf
(20 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
clc1605IST5X
Manufacturer:
CADEKA
Quantity:
20 000
Data Sheet
General Information - Current Feedback
Technology
Advantages of CFB Technology
The CLC1605 Family of amplifiers utilize current feedback
(CFB) technology to achieve superior performance. The
primary advantage of CFB technology is higher slew rate
performance when compared to voltage feedback (VFB)
architecture. High slew rate contributes directly to better
large signal pulse response, full power bandwidth, and
distortion.
CFB also alleviates the traditional trade-off between
closed loop gain and usable bandwidth that is seen with
a VFB amplifier. With CFB, the bandwidth is primarily
determined by the value of the feedback resistor, R
using optimum feedback resistor values, the bandwidth
of a CFB amplifier remains nearly constant with different
gain configurations.
When designing with CFB amplifiers always abide by these
basic rules:
• Use the recommended feedback resistor value
• Do not use reactive (capacitors, diodes, inductors, etc.)
elements in the direct feedback path
• Avoid stray or parasitic capacitance across feedback
resistors
• Follow general high-speed amplifier layout guidelines
• Ensure proper precautions have been made for driving
capacitive loads
©2007-2008 CADEKA Microcircuits LLC
Figure 1. Non-Inverting Gain Configuration with First
V
IN
R g
V
V
I err
OUT
IN
Order Transfer Function
= 1 +
x1
R
R
g
f
Z
o *I err
+
R
1 +
f
Z
1
o(jω)
R
V
f
OUT
Eq. 1
R
L
f
. By
CFB Technology - Theory of Operation
Figure 1 shows a simple representation of a current
feedback amplifier that is configured in the traditional
non-inverting gain configuration.
Instead of having two high-impedance inputs similar to a
VFB amplifier, the inputs of a CFB amplifier are connected
across a unity gain buffer. This buffer has a high impedance
input and a low impedance output. It can source or sink
current (I
to track the value of Vin. The CFB architecture employs
a high gain trans-impedance stage that senses Ierr and
drives the output to a value of (Z
the application of negative feedback, the amplifier will
drive the output to a voltage in a manner which tries to
drive Ierr to zero. In practice, primarily due to limitations
on the value of Z
value.
A closer look at the closed loop transfer function (Eq.1)
shows the effect of the trans-impedance, Z
gain of the circuit. At low frequencies where Z
large with respect to R
approaches unity, allowing R
higher frequencies, the value of Z
the effect of the secondary term will begin to dominate.
The -3dB small signal parameter specifies the frequency
where the value Z
gain to drop by 0.707 of the value at DC.
For
amplifiers, visit www.cadeka.com for detailed application
notes, such as AN-3: The Ins and Outs of Current Feedback
Amplifiers .
Figure 2. Inverting Gain Configuration with First Order
V
IN
more
err
V
R
V
OUT
IN
g
) as needed to force the non-inverting input
information
= −
I err
o
o
(jω) equals the value of R
(jω), Ierr remains a small but finite
R
R
Transfer Function
g
f
f
, the second term of the equation
+
x1
1 +
regarding
Z
f
Z
o *I err
1
and R
o(jω)
R
f
R
o
f
(jω) * I
o
(jω) will roll off, and
g
V
Eq. 2
to set the gain. At
current
www.cadeka.com
OUT
err
) volts. With
o
f
o
(jω) on the
(jω) is very
causing the
feedback
R
L
14