tmp89fm42l TOSHIBA Semiconductor CORPORATION, tmp89fm42l Datasheet - Page 416

• Manufacturer Part Number: tmp89fm42l
• Description: 8 Bit Microcontroller Tlcs-870/c1 Series
• Manufacturer: TOSHIBA Semiconductor CORPORATION

25.3
DC Characteristics
RA002
Supply current in NOR-
MAL 1, 2 modes
(Note 7)
Supply current in
IDLE0, 1, 2 modes
Supply current in
SLOW1 mode
(Notes 5 and 7)
Supply current in
SLEEP1 mode
Supply current in
SLEEP0 mode
Supply current in STOP
mode
Peak current of inter-
mittent operation
(Notes 7 and 9)
Current for writing to
flash memory, erasing
and security program
(Notes 4, 8 and 9)
Parameter
Note 1: Typical values shown are Topr = 25°C and V
Note 2: I
Note 3: V
Note 4: When performing a write or erase on the flash memory or activating a security program in the flash memory, make sure
Note 5: In SLOW1 mode, the difference between the peak current and the average current becomes large.
Note 6: Each supply current in SLOW2 mode is equivalent to that in IDLE0, IDLE1 and IDLE2 modes.
Note 7: When a program operates in the flash memory or when data is being read from the flash memory, the flash memory
Note 8: If a write or erase is performed on the flash memory or a security program is enabled in the flash memory, an instantaneous
Note 9: The circuit of a power supply must be designed such as to enable the supply of a peak current. This peak current causes
Program counter (PC)
that the operating temperature Topr is within the range −10°C to 60°C. If the temperature is outside this range, the resultant
performance cannot be guaranteed.
operates intermittently, and a peak current flows, as shown in Figure 25-4. In this case, the supply current I
MAL1, NORMAL2 and SLOW1 modes) is defined as the sum of the average peak current and MCU current.
peak current flows, as shown in Figure 25-5.
the supply voltage in the device to fluctuate. Connect a bypass capacitor of about 0.1 μF near the power supply of the
device to stabilize its operation.
DD
IN
does not include I
: The input voltage on the pin except MODE pin, V
(Note 8)
Symbol
I
DDRP-P
I
DDEW
I
DD
I
DDP-P
[mA]
Figure 25-4 Intermittent Operation of Flash Memory
1 machine cycle
n
REF
. It is the electrical current in the state in which the peripheral circuitry has been operated.
Pins
n+1
n+2
Page 402
DD
V
V
V
fcgck = 4.2 MHz
fs = 32.768 kHz
V
V
V
fs = 32.768 kHz
V
V
V
V
V
V
V
V
V
DD
IN
MODE
DD
IN
MODE
DD
IN
MODE
DD
IN
MODE
DD
IN
MODE
= 3.0 V, unless otherwise specified.
= 3.4 V/0.2 V
= 2.8 V/0.2 V
= 3.4 V/0.2 V
= 3.4 V/0.2 V
= 3.4 V/0.2 V
= 3.6 V
= 3.0 V
= 3.6 V
= 3.6 V
= 3.6 V
=3.4V/0.1V
=2.8V/0.1V
=3.4V/0.1V
=3.4V/0.1V
=3.4V/0.1V
MODE
n+3
: The input voltage on the MODE pin
Condition
When a program
operates on flash
memory
When a program
operates on RAM
When a program
operates on flash
memory
When a program
operates on RAM
When a program
operates on flash
memory or when
data is being read
from flash memory
Momentary flash current
Maximum current
Typical current
MCU current
Min
−
−
−
−
−
−
−
−
−
−
(V
Sum of average
momentary flash
current and
MCU current
SS
Typ.
= 0 V, Topr = −40 to 85°C)
5.5
3.0
2.0
20
11
10
26
9
8
3
TMP89FM42L
Max
8.0
5.0
3.0
39
30
24
22
17
−
−
DD
(in NOR-
Unit
mA
mA
μA