mc9s08qd4 Freescale Semiconductor, Inc, mc9s08qd4 Datasheet - Page 50
![no-image](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_sml.jpg)
mc9s08qd4
Manufacturer Part Number
mc9s08qd4
Description
Hcs08 Microcontrollers
Manufacturer
Freescale Semiconductor, Inc
Datasheet
1.MC9S08QD4.pdf
(202 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
mc9s08qd4CPC
Manufacturer:
FREESCALE
Quantity:
201
Part Number:
mc9s08qd4CPC
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
mc9s08qd4CSC
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
mc9s08qd4MSC
Manufacturer:
Freescale Semiconductor
Quantity:
150 510
Company:
Part Number:
mc9s08qd4MSC
Manufacturer:
ON
Quantity:
50 000
Chapter 4 Memory Map and Register Definition
4.7.5
50
FACCERR
FBLANK
Reset
FPVIOL
FCBEF
FCCF
Field
7
6
5
4
2
W
R
FCBEF
Flash Status Register (FSTAT)
Flash Command Buffer Empty Flag — The FCBEF bit is used to launch commands. It also indicates that the
command buffer is empty so that a new command sequence can be executed when performing burst
programming. The FCBEF bit is cleared by writing a 1 to it or when a burst program command is transferred to
the array for programming. Only burst program commands can be buffered.
0 Command buffer is full (not ready for additional commands).
1 A new burst program command can be written to the command buffer.
Flash Command Complete Flag — FCCF is set automatically when the command buffer is empty and no
command is being processed. FCCF is cleared automatically when a new command is started (by writing 1 to
FCBEF to register a command). Writing to FCCF has no meaning or effect.
0 Command in progress
1 All commands complete
Protection Violation Flag — FPVIOL is set automatically when FCBEF is cleared to register a command that
attempts to erase or program a location in a protected block (the erroneous command is ignored). FPVIOL is
cleared by writing a 1 to FPVIOL.
0 No protection violation.
1 An attempt was made to erase or program a protected location.
Access Error Flag — FACCERR is set automatically when the proper command sequence is not obeyed exactly
(the erroneous command is ignored), if a program or erase operation is attempted before the FCDIV register has
been initialized, or if the MCU enters stop while a command was in progress. For a more detailed discussion of
the exact actions that are considered access errors, see
writing a 1 to FACCERR. Writing a 0 to FACCERR has no meaning or effect.
0 No access error.
1 An access error has occurred.
Flash Verified as All Blank (erased) Flag — FBLANK is set automatically at the conclusion of a blank check
command if the entire flash array was verified to be erased. FBLANK is cleared by clearing FCBEF to write a new
valid command. Writing to FBLANK has no meaning or effect.
0 After a blank check command is completed and FCCF = 1, FBLANK = 0 indicates the flash array is not
1 After a blank check command is completed and FCCF = 1, FBLANK = 1 indicates the flash array is completely
1
7
completely erased.
erased (all 0xFF).
= Unimplemented or Reserved
FCCF
1
6
Table 4-12. FSTAT Register Field Descriptions
Figure 4-9. Flash Status Register (FSTAT)
MC9S08QD4 Series MCU Data Sheet, Rev. 3
FPVIOL
0
5
FACCERR
0
4
Description
Section 4.5.5, “Access
3
0
0
FBLANK
0
2
Errors.” FACCERR is cleared by
Freescale Semiconductor
0
0
1
0
0
0