am79c930 Advanced Micro Devices, am79c930 Datasheet - Page 23

• Manufacturer Part Number: am79c930
• Description: Pcnet-mobile Single-chip Wireless Lan Media Access Controller
• Manufacturer: Advanced Micro Devices

ISA PLUG AND PLAY PIN SUMMARY
No. of
Pins
17
17
7
8
1
1
1
1
1
1
1
1
6
1
1
1
8
1
1
1
1
1
1
1
1
1
1
1
1
2
LA23–LA17
SA16–SA0
SD7–SD0
RESET
MEMR
MEMW
AEN
BALE
IOCHRDY
IOR
IOW
IRQ4, 5, 9, 10, 11, 12
RFRSH
PCMCIA
PWRDWN
MA16–0
MD7–0
FCE
SCE
XCE
MOE
MWE
TCK
TDI
TDO
TMS
TRST
TEST
CLKIN
PMX1–2
Pin Name
RESET input
Memory Read—used to enable the output drivers of the Am79C930 device for
ISA bus memory read accesses
Memory Write—used to indicate that the current ISA bus cycle is a memory
write access
Bus Address Latch Enable—used to indicate that the ISA address lines are
valid
I/O Read—this signal is asserted by the ISA host system whenever an I/O read
operation occurs
I/O Write—this signal is asserted by the ISA host system whenever an I/O write
operation occurs
Interrupt Request—this line is asserted when the Am79C930 device needs
servicing from the software
Refresh—indicates that the current ISA bus cycle is a refresh operation
Memory Address Bus—these lines are used to address locations in the Flash
device, the SRAM device, and an extra peripheral device that are contained
within an Am79C930-based design
Memory Data Bus—these lines are used to write and read data to/from Flash,
SRAM, and/or an extra peripheral device within an Am79C930-based design
Flash Chip Enable—this signal becomes asserted when the Flash device has
been addressed by either the 80188 core of the Am79C930 device or by the
software through the PCMCIA interface
SRAM Chip Enable—this signal becomes asserted when the SRAM device
has been addressed by either the 80188 core of the Am79C930 device or by
the software through the PCMCIA interface
eXtra Chip Enable—this signal becomes asserted when the extra peripheral
device has been addressed by the 80188 core of the Am79C930 device (XCE
is not accessible through the system interface)
Memory Output Enable—this signal becomes asserted during reads of devices
located on the memory interface bus
Memory Write Enable—this signal becomes asserted during writes to devices
located on the memory interface bus
Test Reset—this is the reset signal for IEEE 1149.1 testing
Test pin—when asserted, this pin places the Am79C930 device into a
non-IEEE 1149.1 test mode
Clock input to drive BIU, 80188 core, and TAI, supplying network data rate
information
ISA upper address bus lines
ISA lower address bus lines
ISA data bus lines
Address Enable—used to indicate that the current ISA bus I/O address is valid
I/O Channel Ready—used to delay the termination of the current ISA bus cycle
PCMCIA mode—selects PCMCIA or ISA Plug and Play mode
Powerdown—indicates that device is in the power down mode
Test Clock—this is the clock signal for IEEE 1149.1 testing
Test Data In—this is the data input signal for IEEE 1149.1 testing
Test Data Out—this is the data output signal for IEEE 1149.1 testing
Test Mode Select—this is the test mode select for IEEE 1149.1 testing
Power Management Xtal—32-kHz Xtal input for sleep timer reference
P R E L I M I N A R Y
Am79C930
Pin Function
PTS3/OD2
Pin Style
TP1
TS1
TP1
TP1
TP1
TP1
TP1
TS2
I/XO
TP1
TS1
TS2
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
23