ST16C2552CJ44 EXAR [Exar Corporation], ST16C2552CJ44 Datasheet - Page 19
![no-image](/images/no-image-200.jpg)
ST16C2552CJ44
Manufacturer Part Number
ST16C2552CJ44
Description
2.97V TO 5.5V DUAL UART WITH 16-BYTE FIFO
Manufacturer
EXAR [Exar Corporation]
Datasheet
1.ST16C2552CJ44.pdf
(36 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ST16C2552CJ44
Manufacturer:
EXAR/艾科嘉
Quantity:
20 000
Company:
Part Number:
ST16C2552CJ44-F
Manufacturer:
XILINX
Quantity:
214
Company:
Part Number:
ST16C2552CJ44-F
Manufacturer:
Exar Corporation
Quantity:
135
Company:
Part Number:
ST16C2552CJ44-F
Manufacturer:
EXAR42
Quantity:
28
Company:
Part Number:
ST16C2552CJ44-F
Manufacturer:
Exar Corporation
Quantity:
10 000
Company:
Part Number:
ST16C2552CJ44TR-F
Manufacturer:
Exar Corporation
Quantity:
10 000
REV. 4.2.1
ISR[3:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Interrupt Source
ISR[5:4]: Reserved
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
•
•
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
•
•
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
•
•
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY# and RXRDY# pins. See DMA operation section for details.
•
•
FCR[5:4]: Reserved
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level.
4.6
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
Logic 0 = No receive FIFO reset (default)
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
FIFO Control Register (FCR) - Write-Only
T
ABLE
9: T
B
FCR
IT
0
0
1
1
RANSMIT AND
-7
B
FCR
IT
0
1
0
1
-6
R
1 (default)
ECEIVE
R
T
L
RIGGER
ECEIVE
EVEL
14
4
8
19
FIFO T
2.97V TO 5.5V DUAL UART WITH 16-BYTE FIFO
Table-A. 16C550,
16C2550, 16C2552,
16C554, 16C580 com-
patible.
RIGGER
C
OMPATIBILITY
Table 9
L
EVEL
shows the complete selections.
S
ELECTION
ST16C2552
Table
8).