LTC3773EG-PBF LINER [Linear Technology], LTC3773EG-PBF Datasheet - Page 11

• Manufacturer Part Number: LTC3773EG-PBF
• Description: Triple Output Synchronous 3-Phase DC/DC Controller with Up/Down Tracking
• Manufacturer: LINER [Linear Technology]

PIN FUNCTIONS
PLLIN/FC (Pin 20/Pin 17): Synchronization Input to the
Phase Detector and Forced Continuous Control Input.
When fl oating, it sits around 1.6V, and the controller enters
discontinuous mode operation at light load. Shorting this
pin low or high for more than 20μs enables Burst Mode
operation or forced continuous current mode operation,
respectively. During frequency synchronization, the phase
locked loop will force the controller to operate in continu-
ous mode and the rising top gate signal of controller 1 to
be synchronized with the rising edge of the PLLIN signal.
When synchronization is not required, it is advisable to
bypass the PLLIN/FC pin with a 1000pF capacitor to avoid
noise coupling.
CLKOUT (Pin 18 UHF Only): CLK Output. Output clock
signal available to synchronize other controller ICs for
additional MOSFET controller stages/phases.
BG3 (Pin 21/Pin 19): Channel 3 Bottom Gate Drive. See
BG1.
PGND (Pin 22/Pin 39): Driver’s Power Ground. This pin
connects directly to the sources of the bottom N-channel
external MOSFETs and the (–) terminals of C
exposed pad (QFN) must be soldered to PCB ground.
V
drivers for the bottom gates. Also used for charging the
bootstrap capacitors. This pin needs to be very carefully
and closely decoupled to the IC’s PGND pin. If the V
potential is lower than V
will be disabled.
BG2 (Pin 24/Pin 21): Channel 2 Bottom Gate Drive. See
BG1.
BG1 (Pin 25/Pin 22): Channel 1 Bottom Gate Drive. Drives
the gate of the bottom N-channel MOSFET between ground
and V
SW3 (Pin 26/Pin 23): Channel 3 Switching Node. See
SW1.
TG3 (Pin 27/Pin 24): Channel 3 Top Gate Drive. See
TG1.
DR
(Pin 23/Pin 20): Driver Supply. Provides supply to the
DR
.
CC
(G/UHF)
potential by 1V, the drivers
IN
. The backside
DR
BOOST3 (Pin 28/Pin 25): Channel 3 Top Gate Driver Sup-
ply. See BOOST1.
BOOST2 (Pin 29/Pin 26): Channel 2 Top Gate Driver Sup-
ply. See BOOST1.
TG2 (Pin 30/Pin 27): Channel 2 Top Gate Drive. See TG1.
SW2 (Pin 31/Pin 28): Channel 2 Switching Node.
See SW1.
SW1 (Pin 32/Pin 29): Channel 1 Switching Node. The (–)
terminal of the bootstrap capacitor connects here. This
pin swings from a Schottky diode (external) voltage drop
below ground to V
supply rail).
TG1 (Pin 33/Pin 30): Channel 1 Top Gate Drive. The TG1
pin drives the top N-channel MOSFET with a voltage
swing equal to V
voltage SW.
BOOST1 (Pin 34/Pin 31): Channel 1 Top Gate Driver Supply.
The (+) terminal of the bootstrap capacitor connects here.
This pin swings from approximately V
(where V
PGOOD (Pin 35/Pin 32): Open Drain Power Good Output.
This open-drain output is pulled low during shutdown or
when any of the three output voltages has been outside
the PGOOD tolerance window for more than 100μs.
PHASEMD (Pin 36/Pin 33): Phase Select Input. This pin
controls the phase relationship between controller 1,
controller 2, controller 3 and CLKOUT. When PHASEMD
is fl oating, its value is around 1.6V, the three channels
switch 120° out of phase, and CLKOUT synchronizes to
the rising edge of TG1. When PHASEMD is grounded,
TG1 leads CLKOUT by 60°. When PHASEMD is shorted
to V
and 180°, respectively.
CC
, TG1 leads TG2, TG3, and CLKOUT by 90°, 270°
IN
is the external MOSFET supply rail).
DR
IN
superimposed on the switch node
(where V
IN
is the external MOSFET
DR
LTC3773
up to V
IN
11
+ V
3773fb
DR