DSP56303 FREESCALE [Freescale Semiconductor, Inc], DSP56303 Datasheet - Page 165
![no-image](/images/no-image-200.jpg)
DSP56303
Manufacturer Part Number
DSP56303
Description
Manufacturer
FREESCALE [Freescale Semiconductor, Inc]
Datasheet
1.DSP56303.pdf
(292 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSP56303AG100
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
DSP56303AG100B1
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
DSP56303AG100R2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
DSP56303GC100
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Part Number:
DSP56303PV100
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Company:
Part Number:
DSP56303PV100B
Manufacturer:
MOT
Quantity:
5 510
Company:
Part Number:
DSP56303PV100B
Manufacturer:
MAXIM
Quantity:
5 510
Company:
Part Number:
DSP56303VF100
Manufacturer:
MNDSPEED
Quantity:
2
Company:
Part Number:
DSP56303VF100
Manufacturer:
MOTOLOLA
Quantity:
513
Company:
Part Number:
DSP56303VF100
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
DSP56303VF100
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
DSP56303VL100
Manufacturer:
FUJI
Quantity:
1 000
RSMA and RSMB (as in Figure 7-12 and Figure 7-13) can be seen as one 32-bit register, RSM.
Bit n in RSM (RSn) is an enable/disable control bit for time slot number N. When RSn is cleared,
all the data signals of the enabled receivers are tri-stated during time slot number N. Data
transfers from the receive data register(s) to the receive shift register(s), but the RDF and ROE
flags are not set. Consequently, during a disabled slot, no receiver full interrupt is generated. The
DSP is interrupted only for enabled slots. When RSn is set, the receive sequence proceeds
normally. Data is received during slot number N, and the RDF flag is set.
When the bits in the RSMx are set, the frame being transmitted is unaffected, but the next frame
transmission is affected. If the RSMx is read, it shows the current setting. When the internal data
bus reads RSMA or RSMB, the register contents occupy the two low-order bytes of the data bus,
and the high-order byte is filled by 0.
After a hardware
$FFFFFFFF, enabling all 32 time slots for data transmission.
7.6 GPIO Signals and Registers
The functionality of each ESSI port is controlled by three registers: port control register (PCRC,
PCRD), port direction register (PRRC, PRRD), and port data register (PDRC, PDRD).
7.6.1 Port Control Registers (PCRC and PCRD)
The read/write 24-bit PCRs control the functionality of the signal lines for ESSI0 and ESSI1.
Each of the PCR bits 5–0 controls the functionality of the corresponding signal line. When a
PCR[i] bit is set, the corresponding port signal is configured as an ESSI signal. When a PCR[i]
bit is cleared, the corresponding port signal is configured as a GPIO signal. Either a hardware
RESET
Freescale Semiconductor
RS27
23
11
signal or a software RESET instruction clears all PCR bits.
–Reserved. Read as zero. Write with zero for future compatibility.
RS26
22
10
RESET
RS25
Figure 7-17. ESSI Receive Slot Mask Register B (RSMB)
21
9
signal or a software RESET instruction, the RSM register is reset to
RS24
20
8
(ESSI0 X:$FFFFB1, ESSI1 X:$FFFFA1)
RS23
DSP56303 User’s Manual, Rev. 2
19
7
RS22
18
6
RS21
17
5
RS20
16
4
RS31
RS19
15
3
GPIO Signals and Registers
RS30
RS18
14
2
RS29
RS17
13
1
RS28
RS16
12
0
7-33