DSP56303 FREESCALE [Freescale Semiconductor, Inc], DSP56303 Datasheet - Page 85
![no-image](/images/no-image-200.jpg)
DSP56303
Manufacturer Part Number
DSP56303
Description
Manufacturer
FREESCALE [Freescale Semiconductor, Inc]
Datasheet
1.DSP56303.pdf
(292 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSP56303AG100
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
DSP56303AG100B1
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
DSP56303AG100R2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
DSP56303GC100
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Part Number:
DSP56303PV100
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Company:
Part Number:
DSP56303PV100B
Manufacturer:
MOT
Quantity:
5 510
Company:
Part Number:
DSP56303PV100B
Manufacturer:
MAXIM
Quantity:
5 510
Company:
Part Number:
DSP56303VF100
Manufacturer:
MNDSPEED
Quantity:
2
Company:
Part Number:
DSP56303VF100
Manufacturer:
MOTOLOLA
Quantity:
513
Company:
Part Number:
DSP56303VF100
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
DSP56303VF100
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
DSP56303VL100
Manufacturer:
FUJI
Quantity:
1 000
Freescale Semiconductor
Number
Bit
7
6
5
4
3
2
Bit Name
BPAC
BYEN
BXEN
BPEN
BAAP
Table 4-10. Address Attribute Registers (AAR[0–3]) Bit Definitions
Reset
Value
0
0
0
0
0
0
Bus Packing Enable
Enables/disables the internal packing/unpacking logic. When BPAC is set, packing is
enabled. In this mode each DMA external access initiates three external accesses to an
8-bit wide external memory (the addresses for these accesses are DAB, then DAB + 1 and
then DAB + 2). Packing to a 24-bit word (or unpacking from a 24-bit word to three 8-bit
words) is done automatically by the expansion port control hardware. The external memory
should reside in the eight Least Significant Bits (LSBs) of the external data bus, and the
packing (or unpacking for external write accesses) occurs in “Little Endian” order (that is,
the low byte is stored in the lowest of the three memory locations and is transferred first; the
middle byte is stored/transferred next; and the high byte is stored/transferred last). When
this bit is cleared, the expansion port control logic assumes a 24-bit wide external memory.
Notes: 1.
Reserved. Write to 0 for future compatibility.
Bus Y Data Memory Enable
A read/write control bit that enables/disables the AA pin and logic during external Y data
space accesses. When set, BYEN enables the comparison of the external address to the
BAC bits during external Y data space accesses. If BYEN is cleared, no address
comparison is performed.
Bus X Data Memory Enable
A read/write control bit that enables/disables the AA pin and logic during external X data
space accesses. When set, BXEN enables the comparison of the external address to the
BAC bits during external X data space accesses. If BXEN is cleared, no address
comparison is performed.
Bus Program Memory Enable
A read/write control bit that enables/disables the AA/RAS pin and logic during external
program space accesses. When set, BPEN enables the comparison of the external address
to the BAC bits during external program space accesses. If BPEN is cleared, no address
comparison is performed.
Bus Address Attribute Polarity
A read/write Bus Address Attribute Polarity (BAAP) control bit that defines whether the
AA/RAS signal is active low or active high. When BAAP is cleared, the AA/RAS signal is
active low (useful for enabling memory modules or for DRAM Row Address Strobe). If
BAAP is set, the appropriate AA/RAS signal is active high (useful as an additional address
bit).
2.
3.
4.
DSP56303 User’s Manual, Rev. 2
BPAC is used only for DMA accesses and not core accesses.
To ensure sequential external accesses, the DMA address should advance
three steps at a time in two-dimensional mode with a row length of one and an
offset size of three. For details, refer to the Freescale application note,
APR23/D, Using the DSP56300 Direct Memory Access Controller.
To prevent improper operation, DMA address + 1 and DMA
address + 2 should not cross the AAR bank borders.
Arbitration is not allowed during the packing access (that is, the three
accesses are treated as one access with respect to arbitration, and the bus
mastership is not released during these accesses).
Description
Bus Interface Unit (BIU) Registers
4-27