CY8C20111_11 CYPRESS [Cypress Semiconductor], CY8C20111_11 Datasheet - Page 29

• Manufacturer Part Number: CY8C20111_11
• Manufacturer: CYPRESS [Cypress Semiconductor]

13.2 DC GPIO Specifications
13.2.1 5-V and 3.3-V DC GPIO Specifications
This table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C ≤ T
guidance only.
13.2.2 2.7-V DC GPIO Specifications
This table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 2.4 V to 2.90 V and
–40 °C < T
13.3 DC POR and LVD Specifications
13.4 DC Flash Write Specifications
This table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40
°C < T
apply to 5 V, 3.3 V, or 2.7 V at 25 °C. These are for design guidance only. Flash Endurance and Retention specifications are valid only
within the range: 25 °C±20 °C during the flash write operation. It is at the user’s own risk to operate out of this temperature range. If
flash writing is done out of this temperature range, the endurance and data retention reduces.
Note
Document Number: 001-53516 Rev. *G
V
V
V
I
I
C
V
V
V
I
I
C
V
V
Parameter
V
I
Flash
Flash
7. Commands involving flash writes (0x01, 0x02, 0x03) and flash read (0x04) must be executed only within the same V
Parameter
OH
OL1
OH
OL1
DDP
Parameter
OH1
OH2
OL
OH1
OH2
OL
PPOR0
PPOR1
OUT
OUT
DDIWRITE
Symbol
command 0x06) and above 2.7 V.
ENPB
DR
A
< 85 °C, 3.10 V to 3.6 V and –40 °C < T
A
A
≤ 85 °C, 3.10 V to 3.6 V –40 °C ≤ T
< 85 °C, respectively. Typical parameters apply to 2.7 V at 25 °C and are for design guidance only.
V
V
V
High output voltage
High output voltage
Low output voltage
High output current
Low output current on Port 0 pins
Capacitive load on pins as output
Supply Voltage for Flash Write Operations
Supply Current for Flash Write Operations
Flash Endurance
Flash Data Retention
High output voltage
High output voltage
Low output voltage
High output current
Low output current on Port 0 pins
Capacitive load on pins as output
DD
DD
DD
= 2.7 V
= 3.3 V, 5 V
Value for PPOR Trip
Description
Description
Description
Description
A
A
< 85 °C or 2.4 V to 2.90 V and –40 °C < T
≤ 85 °C. Typical parameters apply to 5 V and 3.3 V at 25 °C and are for design
V
V
V
V
DD
DD
DD
DD
[7]
0.01
0.01
Min
Min
0.5
0.5
Min
–
–
–
–
– 0.2
– 0.9
– 0.2
– 0.5
–
–
50,000
Min
2.7
10
Typ
2.36
2.60
–
1.7
Typ
Typ
1.7
–
–
–
–
–
–
–
–
–
–
Max
0.75
Max
0.75
Typ
10
Max
2.40
2.65
0.2
1
10
–
–
5
–
5
–
–
–
–
5
Unit
mA
mA
Unit
pF
mA
mA
Unit
V
V
V
pF
Max
V
V
V
25
V
V
–
–
–
I
I
I
mA sink current
V
V
Package and pin dependent.
Temp = 25 °C.
A
OH
OH
OL
I
I
I
current
V
V
Package and pin dependent.
Temp = 25 °C.
V
during startup or reset from watchdog.
OH
OH
OL
DD
DD
DD
DD
< 85 °C, respectively. Typical parameters
DD
CY8C20111, CY8C20121
= 20 mA/pin, V
≤ 10 µA/pin, V
= 1 mA/pin, V
Units
Years
= 10 mA/pin, maximum of 20 mA sink
≤ 10 µA/pin
= 0.2 mA/pin
≥ 3.1 V
≥ 3.1 V, maximum of 40 mA sink current
≤ 2.9 V, maximum of 20 mA sink current
mA
≤ 2.9 V
must be greater than or equal to 2.5 V
CC
V
–
voltage range detected at POR (power on, or
Erase/write cycles
DD
DD
DD
Notes
Notes
Notes
≥ 3.10 V
> 3.10 V, maximum of 40
≥ 3.10 V
Notes
Page 29 of 43
[+] Feedback