LPC1113 NXP [NXP Semiconductors], LPC1113 Datasheet - Page 18

no-image

LPC1113

Manufacturer Part Number
LPC1113
Description
32-bit ARM Cortex-M0 microcontroller; up to 32 kB flash and 8 kB SRAM
Manufacturer
NXP [NXP Semiconductors]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LPC1113F/302
Quantity:
240
Part Number:
LPC1113FBD48
Manufacturer:
NXP
Quantity:
5 000
Part Number:
LPC1113FBD48
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
LPC1113FBD48/301
Manufacturer:
NXP
Quantity:
5 600
Part Number:
LPC1113FBD48/301,1
Manufacturer:
NXP
Quantity:
1 250
Part Number:
LPC1113FBD48/301,1
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
LPC1113FBD48/302
Manufacturer:
FREESCALE
Quantity:
101
Part Number:
LPC1113FBD48/302
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
LPC1113FBD48/302
0
Part Number:
LPC1113FBD48/302,1
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
LPC1113FBD48/303
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
LPC1113FHN33
Manufacturer:
NXP
Quantity:
5 000
Part Number:
LPC1113FHN33
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
LPC1113FHN33/301
Manufacturer:
NXP/恩智浦
Quantity:
20 000
NXP Semiconductors
LPC1111_12_13_14
Product data sheet
7.8.1 Features
7.9.1 Features
7.10 I
7.8 UART
7.9 SPI serial I/O controller
The LPC1111/12/13/14 contain one UART.
Support for RS-485/9-bit mode allows both software address detection and automatic
address detection using 9-bit mode.
The UART includes a fractional baud rate generator. Standard baud rates such as
115200 Bd can be achieved with any crystal frequency above 2 MHz.
The LPC1111/12/13/14 contain two SPI controllers on the LQFP48 package and one SPI
controller on the HVQFN33 packages (SPI0). Both SPI controllers support SSP features.
The SPI controller is capable of operation on a SSP, 4-wire SSI, or Microwire bus. It can
interact with multiple masters and slaves on the bus. Only a single master and a single
slave can communicate on the bus during a given data transfer. The SPI supports full
duplex transfers, with frames of 4 bits to 16 bits of data flowing from the master to the
slave and from the slave to the master. In practice, often only one of these data flows
carries meaningful data.
The LPC1111/12/13/14 contain one I
2
C-bus serial I/O controller
Programmable open-drain mode for parts LPC111x/102/202/302.
Maximum UART data bit rate of 3.125 MBit/s.
16 Byte Receive and Transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
FIFO control mechanism that enables software flow control implementation.
Support for RS-485/9-bit mode.
Support for modem control.
Maximum SPI speed of 25 Mbit/s (master) or 4.17 Mbit/s (slave) (in SSP mode)
Compatible with Motorola SPI, 4-wire Texas Instruments SSI, and National
Semiconductor Microwire buses
Synchronous serial communication
Master or slave operation
8-frame FIFOs for both transmit and receive
4-bit to 16-bit frame
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
2
C-bus controller.
32-bit ARM Cortex-M0 microcontroller
LPC1111/12/13/14
© NXP B.V. 2011. All rights reserved.
18 of 64

Related parts for LPC1113