ST7FLITE29 STMICROELECTRONICS [STMicroelectronics], ST7FLITE29 Datasheet - Page 62
![no-image](/images/no-image-200.jpg)
ST7FLITE29
Manufacturer Part Number
ST7FLITE29
Description
8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet
1.ST7FLITE29.pdf
(131 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ST7FLITE29F286
Manufacturer:
ST
Quantity:
378
Part Number:
ST7FLITE29F2B6
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
ST7FLITE29F2M6TR
Manufacturer:
ST
Quantity:
5 700
Part Number:
ST7FLITE29F2M6TR
Manufacturer:
ST
Quantity:
20 000
ST7LITE2
12-BIT AUTORELOAD TIMER (Cont’d)
Bit 4 = BPEN Break Pin Enable.
This bit is read/write by software and cleared by
hardware after Reset.
0: Break pin disabled
1: Break pin enabled
Bit 3:0 = PWM[3:0] Break Pattern.
These bits are read/write by software and cleared
by hardware after a reset. They are used to force
the four PWMx output signals into a stable state
when the Break function is active.
PWMx DUTY CYCLE REGISTER HIGH (DCRxH)
Read / Write
Reset Value: 0000 0000 (00h)
PWMx DUTY CYCLE REGISTER LOW (DCRxL)
Read / Write
Reset Value: 0000 0000 (00h)
Bits 15:12 = Reserved.
Bits 11:0 = DCR[11:0] PWMx Duty Cycle Value
This 12-bit value is written by software. It defin-
esthe duty cycle of the corresponding PWM output
signal (see
In PWM mode (OEx=1 in the PWMCR register)
the DCR[11:0] bits define the duty cycle of the
PWMx output signal (see
Compare mode, they define the value to be com-
pared with the 12-bit upcounter value.
62/131
1
DCR7 DCR6 DCR5 DCR4 DCR3 DCR2 DCR1 DCR0
15
0
7
0
Figure
0
36).
0
DCR11 DCR10 DCR9 DCR8
Figure
36). In Output
8
0
INPUT CAPTURE REGISTER HIGH (ATICRH)
Read only
Reset Value: 0000 0000 (00h)
INPUT CAPTURE REGISTER LOW (ATICRL)
Read only
Reset Value: 0000 0000 (00h)
Bits 15:12 = Reserved.
Bits 11:0 = ICR[11:0] Input Capture Data .
This is a 12-bit register which is readable by soft-
ware and cleared by hardware after a reset. The
ATICR register contains captured the value of the
12-bit CNTR register when a rising or falling edge
occurs on the ATIC pin. Capture will only be per-
formed when the ICF flag is cleared.
TRANSFER CONTROL REGISTER (TRANCR)
Read/Write
Reset Value: 0000 0001 (01h)
Bits 7:1 Reserved. Forced by hardware to 0.
Bit 0 = TRAN Transfer enable
This bit is read/write by software, cleared by hard-
ware after each completed transfer and set by
hardware after reset.
It allows the value of the DCRx registers to be
transferred to the DCRx shadow registers after the
next overflow event.
The OPx bits are transferred to the shadow OPx
bits in the same way.
ICR7
15
0
7
7
0
ICR6
0
0
ICR5
0
0
ICR4
0
0
ICR11 ICR10
ICR3
0
ICR2
0
ICR9
ICR1
0
TRAN
ICR8
ICR0
8
0
0