71M6543GH MAXIM [Maxim Integrated Products], 71M6543GH Datasheet - Page 20
71M6543GH
Manufacturer Part Number
71M6543GH
Description
Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation
Manufacturer
MAXIM [Maxim Integrated Products]
Datasheet
1.71M6543GH.pdf
(157 pages)
- Current page: 20 of 157
- Download datasheet (3Mb)
disabled, the supply current of the pre-amplifier is <10 nA and the gain is unity. With proper settings of the
PRE_E and DIFF0_E (I/O RAM 0x210C[4]) bits, the pre-amplifier can be used whether differential mode
71M6543F/H and 71M6543G/GH Data Sheet
The recommended ADC multiplexer sequence samples the current first, immediately followed by
sampling of the corresponding phase voltage, thus the voltage is delayed by a phase angle Ф relative to
the current. The delay compensation implemented in the CE aligns the voltage samples with their
corresponding current samples by first delaying the current samples by one full sample interval (i.e.,
360
360
The residual phase error is negligible, and is typically less than ±1.5 milli-degrees at 100Hz, thus it does
not contribute to errors in the energy measurements.
When using remote sensors, the CE performs the same delay compensation described above to align
each voltage sample with its corresponding current sample. Even though the remote current samples do
not pass through the 71M6543 multiplexer, their timing relationship to their corresponding voltages is
fixed and precisely known, provided that the MUXn_SEL[3:0] slot assignment fields are programmed as
shown in
3, 4 and 5, respectively (see
2.2.4
The ADC pre-amplifier is a low-noise differential amplifier with a fixed gain of 8 available only on the
IADC0-IADC1 sensor input pins. A gain of 8 is enabled by setting PRE_E = 1 (I/O RAM 0x2704[5]). When
is selected or not. For best performance, the differential mode is recommended. In order to save power,
the bias current of the pre-amplifier and ADC is adjusted according to the ADC_DIV control bit (I/O RAM
0x2200[5]).
2.2.5
A single 2
resolution of the ADC, including the sign bit, is 21 bits (FIR_LEN[1:0] = 01, I/O RAM 0x210C[2:1]), or 22
bits (FIR_LEN[1:0] = 10). The ADC is clocked by CKADC.
Initiation of each ADC conversion is controlled by the internal MUX_CTRL circuit as described earlier. At
the end of each ADC conversion, the FIR filter output data is stored into the CE RAM location determined by
the multiplexer selection.
2.2.6 FIR Filter
The finite impulse response filter is an integral part of the ADC and it is optimized for use with the multiplexer.
The purpose of the FIR filter is to decimate the ADC output to the desired resolution. At the end of each
ADC conversion, the output data is stored into the fixed CE RAM location determined by the multiplexer
selection stored in the MUXn_SEL[3:0] fields. FIR data is stored after being shifted left by 9 bits.
2.2.7 Voltage References
A bandgap circuit provides the reference voltage to the ADC. The amplifier within the reference is chopper
stabilized, i.e., the chopper circuit can be enabled or disabled by the MPU using the I/O RAM control field
CHOP_E[1:0] (I/O RAM 0x2106[3:2]). The two bits in the CHOP_E[1:0] field enable the MPU to operate the
chopper circuit in regular or inverted operation, or in toggling modes (recommended). When the chopper
circuit is toggled in between multiplexer cycles, dc offsets on VREF are automatically be averaged out,
therefore the chopper circuit should always be configured for one of the toggling modes.
Since the VREF band-gap amplifier is chopper-stabilized, the dc offset voltage, which is the most
significant long-term drift mechanism in the voltage references (VREF), is automatically removed by the
chopper circuit. Both the 71M6543 and the 71M6xx3 feature chopper circuits for their respective VREF
voltage reference.
The general topology of a chopped amplifier is shown in
chip signal and is not accessible on any pin or register.
20
o
o
), then routing the voltage samples through the all-pass filter, thus delaying the voltage samples by
- θ, resulting in the residual phase error between the current and its corresponding voltage of θ – Ф.
ADC Pre-Amplifier
A/D Converter (ADC)
Table
nd
order sigma-delta A/D converter digitizes the voltage and current inputs to the device. The
1. Note that these slot assignments result in VA, VB and VC occupying multiplexer slots
Figure
© 2008–2011 Teridian Semiconductor Corporation
4).
Figure
6. The CROSS signal is an internal on-
v1.2
Related parts for 71M6543GH
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
LCC/M/CIRCUITI INTEGRATI MAXIM
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
KIT/E/MAXIM ANALOG ESSENTIALS # COLLECTION OF PLUG-IN EVALUATION MODULES
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products