71M6543GH MAXIM [Maxim Integrated Products], 71M6543GH Datasheet - Page 79
71M6543GH
Manufacturer Part Number
71M6543GH
Description
Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation
Manufacturer
MAXIM [Maxim Integrated Products]
Datasheet
1.71M6543GH.pdf
(157 pages)
- Current page: 79 of 157
- Download datasheet (3Mb)
71M6543F/H and 71M6543G/GH Data Sheet
3.2.3 SLP Mode
The SLP mode may be commanded by the MPU whenever main system power is absent by asserting the
SLEEP bit (I/O RAM 0x28B2[7]). The purpose of the SLP mode is to consume the least power while still
maintaining the RTC, temperature compensation of the RTC, and the non-volatile portions of the I/O RAM.
In SLP mode, the V3P3D pin is disconnected, removing all sources of leakage from VBAT and V3P3SYS.
The non-volatile memory domain and the basic functions, such as temperature sensor, oscillator, and
RTC, are powered by the VBAT_RTC input. In this mode, the I/O configuration bits, LCD configuration
bits, and NV RAM values are preserved and RTC and oscillator continue to run. This mode can be exited
only by system power-up or one of the wake methods described in
3.4 Wake-Up
Behavior.
If the SLEEP bit is asserted when V3P3SYS pin power is present (i.e., while in MSN mode), the 71M6543
enters SLP mode, resetting the internal WAKE signal, at which point the 71M6543 begins the standard
wake from sleep procedures as described in
3.4 Wake-Up
Behavior.
After the transition from SLP mode to MSN or BRN mode the PC is at 0x0000, the XRAM is in an
undefined state, and the I/O RAM is only partially preserved (see the description of I/O RAM states in
5.2). The non-volatile sections of the I/O RAM are preserved unless RESET goes high.
v1.2
© 2008–2011 Teridian Semiconductor Corporation
79
Related parts for 71M6543GH
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
LCC/M/CIRCUITI INTEGRATI MAXIM
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
KIT/E/MAXIM ANALOG ESSENTIALS # COLLECTION OF PLUG-IN EVALUATION MODULES
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products