71M6543GH MAXIM [Maxim Integrated Products], 71M6543GH Datasheet - Page 78
![no-image](/images/no-image-200.jpg)
71M6543GH
Manufacturer Part Number
71M6543GH
Description
Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation
Manufacturer
MAXIM [Maxim Integrated Products]
Datasheet
1.71M6543GH.pdf
(157 pages)
- Current page: 78 of 157
- Download datasheet (3Mb)
•
•
0x28B2[6]). However, it is recommended that the LCD_ONLY control bit be set by the MPU only after the
71M6543F/H and 71M6543G/GH Data Sheet
3.2.1 BRN Mode
In BRN mode, most non-metering digital functions are active (as shown in
EEPROM, LCD and RTC. In BRN mode, the PLL continues to function at the same frequency as MSN
mode. It is up to the MPU to scale down the PLL (using PLL_FAST, I/O RAM 0x2200[4]) or the MPU
frequency (using MPU_DIV[2:0], I/O RAM 0x2200[2:0]) in order to save power.
From BRN mode, the MPU can choose to enter LCD or SLP modes. When system power is restored
while the 71M6543 is in BRN mode, the part automatically transitions to MSN mode.
The recommended minimum power configuration for BRN mode is as follows:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
3.2.2 LCD Mode
LCD mode may be commanded by the MPU at any time by setting the LCD_ONLY control bit (I/O RAM
71M6543 has entered BRN mode. For example, if the 71M6543 is in MSN mode when LCD_ONLY is set,
the duration of LCD mode is very brief and the 71M6543 immediately 'wakes'.
In LCD mode, V3P3D is disabled, and the VBAT pin supplies the LCD current. Before asserting
LCD_ONLY mode, it is recommended that the MPU minimize PLL current by reducing the output
frequency of the PLL to 6.29 MHz (i.e., write PLL_FAST = 0, I/O RAM 0x2200[4]). The LCD boost system
requires a clock from the PLL for its operation. Thus, if the LCD boost system is enabled (i.e.,
LCD_VMODE[1:0] = 10, I/O RAM 0x2401[7:6]), then the PLL is automatically kept active during LCD
mode, otherwise the PLL is de-activated.
In LCD mode, the data contained in the LCD_SEG registers is displayed using the segment driver pins.
Up to two LCD segments connected to the pins SEGDIO22 and SEGDIO23 can be made to blink without
the involvement of the MPU, which is disabled in LCD mode. To minimize battery power consumption,
only segments that are used should be enabled.
After the transition from LCD mode to MSN or BRN mode, the PC (Program Counter) is at 0x0000, the
XRAM is in an undefined state, and configuration I/O RAM bits are reset (see
upon wake). The data stored in non-volatile I/O RAM locations is preserved in LCD mode (the shaded
locations in
78
RCE0 = 0x00 (I/O RAM 0x2709[7:0]) - remote sensors disabled
LCD_BAT = 1 (I/O RAM 0x2402[7]) - LCD powered from VBAT
LCD_VMODE[1:0] = 0 (I/O RAM 0x2401[7:6]) - 5V LCD boost disabled
CE6 = 0x00 (I/O RAM 0x2106) - CE, RTM and CHOP are disabled
MUX_DIV[3:0] = 0(I/O RAM 0x2100[7:4]) - the ADC multiplexer is disabled
ADC_E = 0 (I/O RAM 0x2704[4]) - ADC disabled
VREF_CAL = 0 (I/O RAM 0x2704[7]) – Vref not driven out
VREF_DIS = 1 (I/O RAM 0x2704[6]) - Vref disabled
PRE_E = 0 (I/O RAM 0x2704[5] - pre-amp disabled
BCURR = 0 (I/O RAM 0x2704[3]) - battery 100µA current load OFF
TMUX[5:0] = 0x0E (I/O RAM 0x2502[5:0]) – TMUXOUT output set to a dc value
TMUX2[4:0] = 0x0E (I/O RAM 0x2503[4:0]) – TMUXOUT2 output set to a dc value
CKGN = 0x24 (I/O RAM 0x2200) - PLL set slow, and MPU_DIV[2:0] (I/O RAM 0x2200[2:0]) set to maximum
TEMP_PER[2:0] = 6 (I/O RAM 0x28A0[2:0]) - temp measurement set to automatic every 512 s
TEMP_BSEL = 1 (I/O RAM 0x28A0[7]) - temperature sensor monitors VBAT
PCON |= 1 (SFR 0x87) - at the end of the main BRN loop, halt the MPU and wait for an interrupt
The baud rate registers are adjusted as needed
All unused interrupts are disabled
Table 71
are non-volatile).
© 2008–2011 Teridian Semiconductor Corporation
Table
Table 71
62) including ICE, UART,
for I/O RAM state
v1.2
Related parts for 71M6543GH
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![5962-89877012C](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
LCC/M/CIRCUITI INTEGRATI MAXIM
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAXPMBAE1#](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
KIT/E/MAXIM ANALOG ESSENTIALS # COLLECTION OF PLUG-IN EVALUATION MODULES
Manufacturer:
Maxim Integrated Products
![MAX3261CCJ](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3263CAG](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX8809AETL+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX1535CETJ+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
![DS2741N+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
![MAX13450EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX13451EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX17497BATE+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
![MAX17502FATB+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
![MAX1978EVKIT](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
![MAX2606EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2608EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2831EVKIT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products