71M6543GH MAXIM [Maxim Integrated Products], 71M6543GH Datasheet - Page 35
71M6543GH
Manufacturer Part Number
71M6543GH
Description
Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation
Manufacturer
MAXIM [Maxim Integrated Products]
Datasheet
1.71M6543GH.pdf
(157 pages)
- Current page: 35 of 157
- Download datasheet (3Mb)
All DIO ports on the chip are bi-directional. Each of them consists of a latch (SFR P0 to P3), an output
driver and an input buffer, therefore the MPU can output or read data through any of these ports. Even if
a DIO pin is configured as an output, the state of the pin can still be read by the MPU, for example when
counting pulses issued via DIO pins that are under CE control.
Clock Stretching (CKCON[2:0], SFR 0x8E)
The CKCON[2:0] field defines the stretch memory cycles that are used for MOVX instructions when
accessing external peripherals. The practical value of this register for the 71M6543 is to guarantee access
to XRAM between CE, MPU, and SPI. The default setting of CKCON[2:0] (001) should be changed to 000
for best performance.
Table 15
from 0 to 7. The widths of the signals are counted in MPU clock cycles. The post-reset state of the
CKCON[2:0] field (001), which is shown in bold in the table, performs the MOVX instructions with a
stretch value equal to 1.
2.4.4 Instruction Set
All instructions of the generic 8051 microcontroller are supported. A complete list of the instruction set
and of the associated op-codes is contained in the 71M654x Software User’s Guide (SUG).
2.4.5 80515 Power Reduction Modes
The 80515 core provides two power reduction modes: Idle Mode and Power-Down Mode. These power
saving modes are invoked by setting the appropriate control bit in the PCON SFR register (SFR 0x87).
Idle Mode halts the MPU while allowing the interrupt, timer, and serial port functions to continue to
operate. Once Idle Mode has been entered, an interrupt event automatically ends Idle Mode. After the
interrupt has been serviced, program execution continues with the instruction immediately following the
instruction that set the Idle Mode bit. To enter Idle Mode, the firmware must set the IDL bit (bit 0) in the
PCON SFR register (SFR 0x87).
v1.2
Name
At power-up SEGDIO0-15 are configured as inputs. It is necessary to write PORT_E = 1 (I/O
RAM 0x270C[5]) to enable SEGDIO0-DIO15. The default PORT_E = 0 blocks any momentary
output transient pulses that would otherwise occur when SEGDIO0-15 are reset on power-up.
SFR
shows how the signals of the External Memory Interface change when stretch values are set
P0
P1
P2
P3
CKCON[2:0]
000
001
010
011
100
101
110
111
Address
SFR
80
90
A0
B0
© 2008–2011 Teridian Semiconductor Corporation
Stretch
Table 14: Port Registers (SEGDIO0-15)
Table 15: Stretch Memory Cycle Width
Value
0
1
2
3
4
5
6
7
D7
DIO_DIR[15:12]
memaddr
DIO_DIR[11:8]
DIO_DIR[3:0]
DIO_DIR[7:4]
Read Signal Width
D6
1
2
3
4
5
6
7
8
D5
memrd
71M6543F/H and 71M6543G/GH Data Sheet
1
2
3
4
5
6
7
8
D4
memaddr
Write Signal Width
D3
2
3
4
5
6
7
8
9
D2
DIO[15:11]
DIO[11:8]
DIO[3:0]
DIO[7:4]
memwr
1
1
2
3
4
5
6
7
D1
D0
35
Related parts for 71M6543GH
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
LCC/M/CIRCUITI INTEGRATI MAXIM
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
KIT/E/MAXIM ANALOG ESSENTIALS # COLLECTION OF PLUG-IN EVALUATION MODULES
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products