A29L320 AMICC [AMIC Technology], A29L320 Datasheet - Page 6

no-image

A29L320

Manufacturer Part Number
A29L320
Description
4M X 8 Bit / 2M X 16 Bit CMOS 3.3 Volt-only, Boot Sector Flash Memory
Manufacturer
AMICC [AMIC Technology]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
A29L320AUV-70IF
Manufacturer:
AMIC
Quantity:
20 000
Write
Accelerated
Program
Standby
Output Disable
Reset
Sector Protect
(Note 2)
Sector Unprotect
(Note 2)
Temporary Sector
Unprotect
Read
Absolute Maximum Ratings*
Storage Temperature Plastic Packages. . . -65°C to + 150°C
Ambient Temperature with Power Applied. -55°C to + 125°C
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . . . . . ……. . -0.5V to +4.0V
A9,
All other pins (Note 1) . . . . . . . . . . …. . -0.5V to VCC + 0.5V
Output Short Circuit Current (Note 3) . . . . . . . …. .
Notes:
1. Minimum DC voltage on input or I/O pins is -0.5V. During
2. Minimum DC input voltage on A9,
3. No more than one output is shorted at a time. Duration of
Device Bus Operations
Legend:
L = Logic Low = V
Notes:
1. Addresses are A20:A0 in word mode (
2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See “Sector/Sector
3. If WP
4. D
PRELIMINARY
This section describes the requirements and use of the
device bus operations, which are initiated through the
internal command register. The command register itself does
not occupy any addressable memory location. The register is
composed of latches that store the commands, along with
the address and data information needed to execute the
Block Protection and Unprotection”.
sector protection depends on whether they were last protected or unprotected using the method described in
“Sector/Sector Block Protection and Unprotection. If WP /ACC = V
Operation
voltage transitions, input or I/O pins may undershoot VSS
to -2.0V for periods of up to 20ns. Maximum DC voltage
on input and I/O pins is VCC +0.5V. During voltage
transitions, input or I/O pins may overshoot to VCC +2.0V
for periods up to 20ns.
0.5V. During voltage transitions, A9,
may overshoot VSS to -2.0V for periods of up to 20ns.
Maximum DC input voltage on A9 is +12.5V which may
overshoot to 14.0V for periods up to 20ns.
the short circuit should not be greater than one second.
OE
IN
or D
& RESET (Note 2) . . . . . . . . . . . …. -0.5 to +12.5V
/ACC=V
OUT
as required by command sequence, data polling, or sector protection algorithm.
IL
, H = Logic High = V
(September, 2005, Version 0.0)
VCC ±
IL
0.3 V
, the two outermost boot sectors remain protected. If WP /ACC=V
CE
X
X
L
L
L
L
L
L
OE
H
H
H
H
H
L
X
X
X
WE
H
X
H
X
X
L
L
L
L
IH
OE
, V
RESET
BYTE
VCC ±
ID
Table 1. A29L320 Device Bus Operations
0.3 V
and RESET is
= 12.0 ± 0.5V, X = Don't Care, D
OE
H
H
H
H
X
X
L
L
=V
and RESET
IH
(Note 3)
(Note 3)
(Note 3)
), A20: A
ACC
200mA
V
WP /
L/H
L/H
L/H
L/H
H
HH
-
-1
A6=H, A1=H, A0=L
A6=L, A1=H, A0=L
Sector Address,
Sector Address,
in byte mode (
5
A0 - A20
(Note 1)
*Comments
Stresses above those listed under "Absolute Maximum
Ratings" may cause permanent damage to this device.
These are stress ratings only. Functional operation of
this device at these or any other conditions above
those indicated in the operational sections of these
specification is not implied or intended. Exposure to
the absolute maximum rating conditions for extended periods
may affect device reliability.
Operating Ranges
Commercial (C) Devices
Ambient Temperature (T
Extended Range Devices
Ambient Temperature (T
For –I series. . . . . . . . . . . . . . . . . . . . . . . . . . -25°C to +85°C
For –U series . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
VCC Supply Voltages
VCC for all devices . . . . . . . . . . . . . . . . . …...+3.0V to +3.6V
Operating ranges define those limits between which the
functionally of the device is guaranteed.
command. The contents of the register serve as inputs to the
internal state machine. The state machine outputs dictate the
function of the device. The appropriate device bus operations
table lists the inputs and control levels required, and the
resulting output. The following subsections describe each of
these operations in further detail.
A
A
A
A
X
X
X
IN
IN
IN
IN
IN
HH
= Data In, D
BYTE =V
, all sectors are unprotected.
I/O
(Note 4)
(Note 4)
(Note 4)
(Note 4)
(Note 4)
High-Z
High-Z
High-Z
D
0
OUT
- I/O
IL
OUT
).
A
A
7
= Data Out, A
) . . . . . . . . . . . ….. . . 0°C to +70°C
)
AMIC Technology, Corp.
BYTE
(Note 4)
(Note 4)
(Note 4)
High-Z
High-Z
High-Z
D
IH
OUT
X
X
, the two outermost boot
=V
A29L320 Series
I/O
IH
IN
= Address In
8
I/O
- I/O
8
BYTE
~I/O
I/O
High-Z
High-Z
High-Z
High-Z
High-Z
15
15
14
X
X
=A
=High-Z
=V
-1
IL

Related parts for A29L320