X40626V14I Xicor, X40626V14I Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/7/721/xicor_sml.jpg)
X40626V14I
Manufacturer Part Number
X40626V14I
Description
Dual Voltage CPU Supervisor with 64K Serial EEPROM
Manufacturer
Xicor
Datasheet
1.X40626V14I.pdf
(23 pages)
X40626
ABSOLUTE MAXIMUM RATINGS
Temperature under bias ................... -65°C to +135°C
Storage temperature ........................ -65°C to +150°C
Voltage on any pin with respect to VSS ....-1.0V to +7V
D.C. output current (sink).................................... 10mA
Lead temperature (soldering, 10 seconds).........300°C
Table 2. Recommended Operating Conditions
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Notes: (1) The device enters the Active state after any start, and remains active until: (a) 9 clock cycles later if the Device Select Bits in the
REV 1.1.15 2/11/04
I
I
I
I
I
I
V
V
V
V
Symbol
CC1
CC2
SB1
SB2
LI
LO
IL
IH
HYS
OL
Commercial
Industrial
(2)
(3)
(1)
(2)
Temp
(2) The device enters the Active state after any start, and remains active until t
(3) The device goes into Standby: (a) 200nS after any stop, except those that initiate a nonvolatile write cycle; or (b) t
Slave Address Byte are incorrect; or (b) 200nS after a stop ending a read operation.
that initiates a nonvolatile cycle; or 9 clock cycles after any start that is not followed by the correct Device Select Bits in the Slave
Address Byte.
Active Supply Current Read
Active Supply Current Write
Standby Current DC (WDT off)
Standby Current DC (WDT on)
Input Leakage Current
Output Leakage Current
Input LOW Voltage
Input HIGH Voltage
Schmitt Trigger Input Hysteresis
Output LOW Voltage
Parameter
-40°C
Min.
0°C
V
Fixed input level
CC
related level
+85°C
Max.
70°C
V
.05 x V
www.xicor.com
CC
V
Min
0.2
CC
-1
x 0.7
CC
= 2.7 to 5.5V
COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device (at these or any other conditions above those
listed in the operational sections of this specification) is
not implied. Exposure to absolute maximum rating con-
ditions for extended periods may affect device reliability.
V
V
CC
CC
Max
1.0
3.0
0.4
30
10
10
1
x 0.3
+0.5
WC
after a stop ending a write operation.
Unit
mA
mA
µA
µA
µA
µA
V
V
V
V
V
Characteristics subject to change without notice.
V
f
V
Others=GND or V
V
Others=GND or V
V
V
Device is in Standby
I
I
SCL
OL
OL
IL
SDA
SDA
IN
SDA
= V
= 1.0mA (V
= 3.0mA (V
= GND to V
= 400KHz, SDA = Open
=V
=V
= GND to V
Test Conditions
CC
SCL
SCL
x 0.1, V
=V
=V
CC
CC
CC
CC
CC
CC
CC
CC
=3V)
=5V)
IH
= V
WC
CC
after a stop
15 of 23
x 0.9