K9F1208Q0A-XXB0 Samsung semiconductor, K9F1208Q0A-XXB0 Datasheet - Page 30

• Manufacturer Part Number: K9F1208Q0A-XXB0
• Description: 512Mb/256Mb 1.8V NAND Flash Errata
• Manufacturer: Samsung semiconductor

K9F5608U0C-VCB0,VIB0,FCB0,FIB0
K9F5608Q0C-DCB0,DIB0,HCB0,HIB0
K9F5608U0C-YCB0,YIB0,PCB0,PIB0
K9F5608U0C-DCB0,DIB0,HCB0,HIB0
The device is programmed basically on a page basis, but it does allow multiple partial page programing of a byte/word or consecutive
bytes/words up to 528
ming operation within the same page without an intervening erase operation should not exceed 2 for main array and 3 for spare
array. The addressing may be done in any random order in a block. A page program cycle consists of a serial data loading period in
which up to 528 bytes
gramming period where the loaded data is programmed into the appropriate cell. About the pointer operation, please refer to the
attached technical notes.
The serial data loading period begins by inputting the Serial Data Input command(80h), followed by the three cycle address input and
then serial data loading. The words other than those to be programmed do not need to be loaded.The Page Program confirm com-
mand(10h) initiates the programming process. Writing 10h alone without previously entering the serial data will not initiate the pro-
gramming process. The internal write controller automatically executes the algorithms and timings necessary for program and verify,
thereby freeing the system controller for other tasks. Once the program process starts, the Read Status Register command may be
entered, with RE and CE low, to read the status register. The system controller can detect the completion of a program cycle by
monitoring the R/B output, or the Status bit(I/O 6) of the Status Register. Only the Read Status command and Reset command are
valid while programming is in progress. When the Page Program is complete, the Write Status Bit(I/O 0) may be checked(Figure 10).
The internal write verify detects only errors for "1"s that are not successfully programmed to "0"s. The command register remains in
Read Status command mode until another valid command is written to the command register.
COPY-BACK PROGRAM
The copy-back program is configured to quickly and efficiently rewrite data stored in one page within the array to another page within
the same array without utilizing an external memory. Since the time-consuming sequently-reading and its re-loading cycles are
removed, the system performance is improved. The benefit is especially obvious when a portion of a block is updated and the rest of
the block also need to be copied to the newly assigned free block. The operation for performing a copy-back is a sequential execu-
tion of page-read without burst-reading cycle and copying-program with the address of destination page. A normal read operation
with "00h" command with the address of the source page moves the whole 528bytes/264words(X8 device:528bytes, X16
device:264words) data into the internal buffer. As soon as the Flash returns to Ready state, copy-back programming command "8Ah"
may be given with three address cycles of target page followed. The data stored in the internal buffer is then programmed directly
into the memory cells of the destination page. Once the Copy-Back Program is finished, any additional partial page programming into
the copied pages is prohibited before erase. Since the memory array is internally partitioned into two different planes, copy-back pro-
gram is allowed only within the same memory plane. Thus, A14, the plane address, of source and destination page address must be
the same.
PAGE PROGRAM
Figure 10. Program Operation
Figure 11. Copy-Back Program Operation
R/B
R/B
I/Ox
I/Ox
00h
80h
(X8 device)
(X8 device) or
Source Address
Add.(3Cycles)
Address & Data Input
or 264 words
264
(X16 device)
t
R
(X16 device)
K9F5616Q0C-DCB0,DIB0,HCB0,HIB0
K9F5616U0C-YCB0,YIB0,PCB0,PIB0
K9F5616U0C-DCB0,DIB0,HCB0,HIB0
, in a single page program cycle. The number of consecutive partial page program-
10h
8Ah
of data may be loaded into the page register, followed by a non-volatile pro-
Destination Address
Add.(3Cycles)
29
t
PROG
t
PROG
70h
70h
FLASH MEMORY
Fail
I/O
I/O
Fail
0
0
Pass
Pass