CX28344 Conexant, CX28344 Datasheet - Page 110
CX28344
Manufacturer Part Number
CX28344
Description
(CX2834x) Dual / Triple / Quad / Hex / Octal - Enhanced DS3 / E3 Framer
Manufacturer
Conexant
Datasheet
1.CX28344.pdf
(195 pages)
- Current page: 110 of 195
- Download datasheet (2Mb)
Functional Description
2.4.4
2-64
Source Loopback
in loopback). Idle pattern and RAI transmission due to TxAlm bits are also valid
during this loopback.
When TxLOS bit in Feature2 Control register is set, an all-0s signal is output on the
transmitter and overrides the content of the frame looped from the receiver.
This loopback is activated by setting PayldLp bit in the Feature3 Control register.
The source loopback loops the transmitter encoder outputs back to the system through
the receiver decoder inputs. The receiver dejitter FIFO is meaningless in this mode,
since there is only one clock looped back from the transmitter circuit, TCLKO clock.
The transmitter data path is not affected by activation of this loopback and the
transmitted data is still present on TXPOS and TXNEG pins. The transmitted frame
can be overwritten by an AIS pattern by setting TxAlm bits in Mode Control register
to AIS control state. Doing this affects only TXPOS and TXNEG and not the looped
frame. Therefore, there is no way to generate an AIS pattern on the looped frame by
the transmitter. The same behavior applies to TxLOS bit. I.e., when TxLOS is set
during source loopback only TXPOS and TXNEG are forced to zero, the looped
frame is unaffected. When an AIS or LOS pattern is generated error insertion is
invalid. Idle pattern and RAI are not supported in this mode like AIS; i.e., they can
overwrite the looped frame by setting TxAlm bits as in normal operation.
Setting SourceLp bit in the Mode Control register activates this loopback.
NOTE:
NOTE:
Mindspeed Technologies™
The transmitter does not generate an AIS or Idle pattern independently due to AIS or
Idle detection in the receiver during this loopback. The microprocessor must
program the transmitter to generate an AIS/Idle according to the receiver detection.
The shallow line loopback and source loopback cannot be operated simultaneously.
CX28342/3/4/6/8 Data Sheet
28348-DSH-001-B
Related parts for CX28344
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Bluetooth RF Transceiver
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Bluetooth RF Transceiver
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
ATM transmitter/receiver with UTOPIA interface
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Service SAR controller
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
CN8223EPFATM Transmitter/Receiver with UTOPIA Interface
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Embedded modem family
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Fully integrated T1/E1 framer and line interface
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Flicker-free video encoder
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Home Networking Physical Layer Device with Integrated Analog Front End Circuitry Data Sheet (Preliminary) CX82100-41Home Network Processor (HNP)
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Flicker-free video encoder
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
SmartV.XX Modem
Manufacturer:
Conexant Systems, Inc.
Datasheet:
Part Number:
Description:
Multichannel synchronous communications controller
Manufacturer:
Conexant Systems, Inc.
Datasheet: