ZL50018 ZARLINK [Zarlink Semiconductor Inc], ZL50018 Datasheet - Page 35
![no-image](/images/no-image-200.jpg)
ZL50018
Manufacturer Part Number
ZL50018
Description
2 K Digital Switch with Enhanced Stratum 3 DPLL
Manufacturer
ZARLINK [Zarlink Semiconductor Inc]
Datasheet
1.ZL50018.pdf
(136 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ZL50018GA
Manufacturer:
ZARLINK
Quantity:
5
Company:
Part Number:
ZL50018GAG2
Manufacturer:
TECCOR
Quantity:
5 600
Company:
Part Number:
ZL50018QCG1
Manufacturer:
ZARLINK
Quantity:
201
Company:
Part Number:
ZL50018QCG1
Manufacturer:
ZARLINK
Quantity:
81
9.0
The connection memory consists of two blocks, Connection Memory Low (CM_L) and Connection Memory High
(CM_H). The CM_L is 16 bits wide and is used for channel switching and other special modes. The CM_H is 5 bits
wide and is used for the voice coding function. When UAEN (bit 15) of the Connection Memory Low (CM_L) is low,
µ-law/A-law conversion will be turned off and the contents of CM_H will be ignored. Each connection memory
location of the CM_L or CM_H can be read or written via the 16 bit microprocessor port within one microprocessor
access cycle. See Table 68 on page 100 for the address mapping of the connection memory. Any unused bits will
be reset to zero on the 16-bit data bus.
For the normal channel switching operation, CMM (bit 0) of the Connection Memory Low (CM_L) is programmed
low. SCA7 - 0 (bits 8 - 1) indicate the source (input) channel address and SSA4 - 0 (bits 13 - 9) indicate the source
(input) stream address. The 5-bit contents of the CM_H will be ignored during the normal channel switching mode
without the µ-law/A-law conversion when UAEN (bit 15) of the Connection Memory Low (CM_L) is set to zero. If
µ-law/A-law conversion is required, the CM_H bits must be programmed first to provide the voice/data information,
the input coding law and the output coding law before the assertion of UAEN (bit 15) in the Connection Memory
Low.
When CMM (bit 0) of the Connection Memory Low (CM_L) is programmed high, the ZL50018 will operate in one of
the special modes described in Table 70 on page 102. When the per-channel message mode is enabled, MSG7 - 0
(bit 10 - 3) in the Connection Memory Low (CM_L) will be output via the serial data stream as message output data.
When the per-channel message mode is enabled, the µ-law/A-law conversion can also be enabled as required.
STio
STio
STi
STi
L = last channel = 31, 63, 127, or 255 for 2.048 Mbps, 4.096 Mbps, 8.192 Mbps, or 16.384 Mbps respectively.
L-2 L-1 CH0 CH1 CH2 CH3
L-2 L-1 CH0 CH1 CH2 CH3
L-2 L-1 CH0 CH1 CH2 CH3
L-2 L-1 CH0 CH1 CH2 CH3
Connection Memory Description
Figure 20 - Data Throughput Delay for Constant Delay
Frame N
L-2 L-1 CH0 CH1 CH2 CH3
L-2 L-1 CH0 CH1 CH2 CH3
L-2 L-1 CH0 CH1 CH2 CH3
L-2 L-1 CH0 CH1 CH2 CH3
Zarlink Semiconductor Inc.
ZL50018
35
Frame N + 1
L-2 L-1 CH0 CH1 CH2 CH3
L-2 L-1 CH0 CH1 CH2 CH3
L-2 L-1 CH0 CH1 CH2 CH3
L-2 L-1 CH0 CH1 CH2 CH3
Data Sheet
Frame N + 2