K4H510438G SAMSUNG [Samsung semiconductor], K4H510438G Datasheet

no-image

K4H510438G

Manufacturer Part Number
K4H510438G
Description
512Mb G-die DDR SDRAM Specification
Manufacturer
SAMSUNG [Samsung semiconductor]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
K4H510438G-HCCC
Manufacturer:
SAMSUNG
Quantity:
12 651
Part Number:
K4H510438G-HCCC
Manufacturer:
PHI
Quantity:
2 000
K4H510438G
K4H510838G
K4H511638G
512Mb G-die DDR SDRAM Specification
INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO SAMSUNG PRODUCTS,
AND IS SUBJECT TO CHANGE WITHOUT NOTICE. NOTHING IN THIS DOCUMENT SHALL BE
CONSTRUED AS GRANTING ANY LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHER-
WISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IN SAMSUNG PRODUCTS OR TECHNOL-
OGY. ALL INFORMATION IN THIS DOCUMENT IS PROVIDED ON AS "AS IS" BASIS WITHOUT
GUARANTEE OR WARRANTY OF ANY KIND.
1. For updates or additional information about Samsung products, contact your nearest Samsung office.
2. Samsung products are not intended for use in life support, critical care, medical, safety equipment, or similar
* Samsung Electronics reserves the right to change products or specification without notice.
applications where Product failure could result in loss of life or personal or physical harm, or any military or
defense application, or any governmental procurement to which special terms or provisions may apply.
with Lead-Free and Halogen-Free
(RoHS compliant)
66 TSOP-II
1 of 24
Rev. 1.1 November 2009
DDR SDRAM

Related parts for K4H510438G

K4H510438G Summary of contents

Page 1

... K4H510438G K4H510838G K4H511638G 512Mb G-die DDR SDRAM Specification with Lead-Free and Halogen-Free INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO SAMSUNG PRODUCTS, AND IS SUBJECT TO CHANGE WITHOUT NOTICE. NOTHING IN THIS DOCUMENT SHALL BE CONSTRUED AS GRANTING ANY LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHER- WISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IN SAMSUNG PRODUCTS OR TECHNOL- OGY. ALL INFORMATION IN THIS DOCUMENT IS PROVIDED ON AS " ...

Page 2

... K4H510438G K4H510838G K4H511638G Table of Contents 1.0 Key Features ...............................................................................................................................4 2.0 Ordering Information ...................................................................................................................4 3.0 Operating Frequencies................................................................................................................4 4.0 Pin Description ............................................................................................................................5 5.0 Package Physical Dimension .....................................................................................................6 6.0 Block Diagram (32Mbit 16Mbit x8 / 8Mbit x16 I/O x4 Banks)............................................7 7.0 Input/Output Function Description ............................................................................................8 8.0 Command Truth Table.................................................................................................................9 9.0 General Description...................................................................................................................10 10.0 Absolute Maximum Rating .....................................................................................................10 11.0 DC Operating Conditions ........................................................................................................10 12.0 DDR SDRAM IDD Spec Items & Test Conditions ..................................................................11 13.0 Input/Output Capacitance ......................................................................................................11 14.0 Detailed test condition for DDR SDRAM IDD1 & ...

Page 3

... K4H510438G K4H510838G K4H511638G Revision History Revision Month Year 1.0 September 2009 1.1 November 2009 - Initial Release - Changed tRAS max data of -BO(266Mbps) on page DDR SDRAM History Rev. 1.1 November 2009 ...

Page 4

... Lead-Free & Halogen-Free • RoHS compliant 2.0 Ordering Information Part No. Org. K4H510438G-LC/LB0 128M x 4 K4H510438G-LC/LB3 K4H510838G-LC/LCC 64M x 8 K4H510838G-LC/LB3 K4H511638G-LC/LCC 32M x 16 K4H511638G-LC/LB3 Note : 1. "L" of part number(12th digit) stands for RoHS compliant and Halogen-Free product. ...

Page 5

... K4H510438G K4H510838G K4H511638G 4.0 Pin Description DDQ DDQ SSQ SSQ DDQ DDQ SSQ SSQ DDQ DDQ LDQS LDM ...

Page 6

... K4H510438G K4H510838G K4H511638G 5.0 Package Physical Dimension #66 #1 (1.50) 0.65TYP (0.71) [0.65 0.08] ± NOTE REFERENCE ASS’Y OUT QUALITY #34 #33 22.22 0.10 ± (10°) (10°) Detail A Detail B Detail A Detail B 0.25 ± 0.08 0.30 ± 0.08 66Pin TSOP(II) Package Dimension DDR SDRAM +0.075 0.125 - 0.035 0.10 MAX [ [ 0.075 MAX Rev. 1.1 November 2009 Unit : mm 0 ...

Page 7

... K4H510438G K4H510838G K4H511638G 6.0 Block Diagram (32M 16Mb 8Mb x 16 I/O x4 Banks) Bank Select CK, CK ADD LCKE LRAS LCBR CK, CK CKE x4/x8/16 CK, CK Data Input Register Serial to parallel x8/x16/32 16Mx8/ 8Mx16/ 4Mx32 16Mx8/ 8Mx16/ 4Mx32 16Mx8/ 8Mx16/ 4Mx32 16Mx8/ 8Mx16/ 4Mx32 Column Decoder Latency & ...

Page 8

... K4H510438G K4H510838G K4H511638G 7.0 Input/Output Function Description SYMBOL TYPE CK, CK Input CKE Input CS Input RAS, CAS, WE Input LDM,(UDM) Input BA0, BA1 Input 12] Input DQ I/O LDQS,(U)DQS I Supply DDQ V Supply SSQ V Supply DD V Supply SS V Input REF Clock : CK and CK are differential clock inputs. All address and control input signals are sam- pled on the positive edge of CK and negative edge of CK ...

Page 9

... K4H510438G K4H510838G K4H511638G 8.0 Command Truth Table COMMAND Register Extended MRS Register Mode Register Set Auto Refresh Entry Refresh Self Refresh Bank Active & Row Addr. Read & Auto Precharge Disable Column Address Auto Precharge Enable Write & Auto Precharge Disable Column Address ...

Page 10

... Banks / 16M x 8Bit x 4 Banks / 8M x 16Bit x 4 Banks Double Data Rate SDRAM 9.0 General Description The K4H510438G / K4H510838G / K4H511638G is 536,870,912 bits of double data rate synchronous DRAM organized as 4x 33,554,432 / 4x 16,777,216 / 4x 8,388,608 words by 4/8/16bits, fabricated with SAMSUNG′s high performance CMOS technology. Syn- chronous features with Data Strobe allow extremely high performance up to 400Mb/s per pin ...

Page 11

... K4H510438G K4H510838G K4H511638G 12.0 DDR SDRAM IDD Spec Items & Test Conditions Operating current - One bank Active-Precharge; tRC=tRCmin; tCK=7.5ns for DDR266, 6ns for DDR333, 5ns for DDR400; DQ,DM and DQS inputs changing once per clock cycle; address and control inputs changing once every two clock cycles. ...

Page 12

... K4H510438G K4H510838G K4H511638G 14.0 Detailed test condition for DDR SDRAM IDD1 & IDD7A IDD1 : Operating current: One bank operation 1. Typical Case: For DDR266,333: V Worst Case : V = 2.7V, T= 10° Only one bank is accessed with tRC(min), Burst Mode, Address and Control inputs on NOP edge are changing once per clock cycle ...

Page 13

... IDD4R IDD4W IDD5 Normal IDD6 Low power IDD7A Symbol CC(DDR400@CL=3) IDD0 IDD1 IDD2P IDD2F IDD2Q IDD3P IDD3N IDD4R IDD4W IDD5 Normal IDD6 Low power IDD7A 128Mx4 (K4H510438G 110 5 3 210 64Mx8 (K4H510838G 110 110 ...

Page 14

... K4H510438G K4H510838G K4H511638G 16.0 AC Operating Conditions Parameter/Condition Input High (Logic 1) Voltage, DQ, DQS and DM signals Input Low (Logic 0) Voltage, DQ, DQS and DM signals. Input Differential Voltage, CK and CK inputs Input Crossing Point Voltage, CK and CK inputs Note : the magnitude of the difference between the input level on CK and the input level on CK. ...

Page 15

... K4H510438G K4H510838G K4H511638G 18.0 Overshoot/Undershoot specification for Data, Strobe and Mask Pins Maximum peak amplitude allowed for overshoot Maximum peak amplitude allowed for undershoot The area between the overshoot signal and V The area between the undershoot signal and GND must be less than or equal to ...

Page 16

... K4H510438G K4H510838G K4H511638G 19.0 AC Timming Parameters & Specifications Parameter Row cycle time Refresh row cycle time Row active time RAS to CAS delay Row precharge time Row active to Row active delay Write recovery time Last data in to Read command Clock cycle time CL=2.0 CL=2.5 CL=3.0 Clock high level width ...

Page 17

... K4H510438G K4H510838G K4H511638G 20.0 System Characteristics for DDR SDRAM The following specification parameters are required in systems using DDR333, DDR266 & DDR400 devices to ensure proper system performance. these characteristics are for system simulation purposes and are guaranteed by design. Table 1 : Input Slew Rate for DQ, DQS, and DM ...

Page 18

... K4H510438G K4H510838G K4H511638G 21.0 Component Notes 1. All voltages referenced to Vss. 2. Tests for ac timing, IDD, and electrical, ac and dc characteristics, may be conducted at nominal reference/supply voltage levels, but the related specifications and device operation are guaranteed for the full voltage range specified. 3. Figure 1 represents the timing reference load used in defining the relevant timing parameters of the part not intended to be either a precise representation of the typical system environment nor a depiction of the actual load presented by a production tester ...

Page 19

... K4H510438G K4H510838G K4H511638G Component Notes 17. For CK & CK slew rate ≥ 1.0 V/ns 18. These parameters guarantee device timing, but they are not necessarily tested on each device. They may be guaranteed by device design or tester correlation. 19. Slew Rate is measured between V 20. Min (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this value can be greater than the minimum specification limits for tCL and tCH) ...

Page 20

... K4H510438G K4H510838G K4H511638G 22.0 System Notes a. Pullup slew rate is characteristized under the test conditions as shown in Figure 2. Output Figure 2 : Pullup slew rate test load b. Pulldown slew rate is measured under the test conditions shown in Figure 3. Output Figure 3 : Pulldown slew rate test load c. Pullup slew rate is measured between (V ...

Page 21

... K4H510438G K4H510838G K4H511638G 23.0 IBIS : I/V Characteristics for Input and Output Buffers DDR SDRAM Output Driver V-I Characteristics DDR SDRAM Output driver characteristics are defined for full and half strength operation as selected by the EMRS bit A1. Figures 4 and 5 show the driver characteristics graphically, and tables 8 and 9 show the same data in tabular format suitable for input into simulation tools ...

Page 22

... K4H510438G K4H510838G K4H511638G Pulldown Current (mA) Typical Typical Voltage (V) Low High 0.1 6.0 6.8 0.2 12.2 13.5 0.3 18.1 20.1 0.4 24.1 26.6 0.5 29.8 33.0 0.6 34.6 39.1 0.7 39.4 44.2 0.8 43.7 49.8 0.9 47.5 55.2 1.0 51.3 60.3 1.1 54.1 65.2 1.2 56.2 69.9 1.3 57.9 74.2 1.4 59.3 78.4 1.5 60.1 82.3 1.6 60.5 85.9 1.7 61.0 89.1 1.8 61.5 92.2 1.9 62.0 95.3 2.0 62.5 97.2 2.1 62.9 99.1 2.2 63.3 100.9 2.3 63.8 101.9 2.4 64.1 102.8 2.5 64.6 103.8 2.6 64.8 104.6 2.7 65.0 105.4 Minimum Maximum 4.6 9.6 9.2 18.2 13.8 26.0 18.4 33.9 23.0 41.8 27.7 49.4 32.2 56.8 36.8 63.2 39.6 69.9 42.6 76.3 44.8 82.5 46.2 88.3 47.1 93.8 47.4 99.1 47.7 103.8 48.0 108.4 48.4 112.1 48.9 115.9 49.1 119.6 49.4 123.3 49.6 126.5 49.8 129.5 49.9 132.4 50.0 135.0 50.2 137.3 50.4 139.2 50.5 140.8 Table 8. Full Strength Driver Characteristics DDR SDRAM pullup Current (mA) ...

Page 23

... K4H510438G K4H510838G K4H511638G 0.0 Pulldown Characteristics for Weak Output Driver 0.0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 Pullup Characteristics for Weak Output Driver Figure 5. I/V characteristics for input/output buffers:Pulldown(above) and pullup(below) 1.0 2.0 1.0 2 DDR SDRAM Maximum Typical High Typical Low Minimum ...

Page 24

... K4H510438G K4H510838G K4H511638G Pulldown Current (mA) Typical Typical Voltage (V) Low High 0.1 3.4 3.8 0.2 6.9 7.6 0.3 10.3 11.4 0.4 13.6 15.1 0.5 16.9 18.7 0.6 19.6 22.1 0.7 22.3 25.0 0.8 24.7 28.2 0.9 26.9 31.3 1.0 29.0 34.1 1.1 30.6 36.9 1.2 31.8 39.5 1.3 32.8 42.0 1.4 33.5 44.4 1.5 34.0 46.6 1.6 34.3 48.6 1.7 34.5 50.5 1.8 34.8 52.2 1.9 35.1 53.9 2.0 35.4 55.0 2.1 35.6 56.1 2.2 35.8 57.1 2.3 36.1 57.7 2.4 36.3 58.2 2.5 36.5 58.7 2.6 36.7 59.2 2.7 36.8 59.6 Minimum Maximum 2.6 5.0 5.2 9.9 7.8 14.6 10.4 19.2 13.0 23.6 15.7 28.0 18.2 32.2 20.8 35.8 22.4 39.5 24.1 43.2 25.4 46.7 26.2 50.0 26.6 53.1 26.8 56.1 27.0 58.7 27.2 61.4 27.4 63.5 27.7 65.6 27.8 67.7 28.0 69.8 28.1 71.6 28.2 73.3 28.3 74.9 28.3 76.4 28.4 77.7 28.5 78.8 28.6 79.7 Table 9. Weak Driver Characteristics DDR SDRAM pullup Current (mA) Typical Typical Minimum Low High -3.5 -4.3 -2.6 -6.9 -8.2 -5.2 -10.3 -12.0 -7.8 -13.6 -15.7 -10.4 -16.9 -19.3 -13.0 -19.4 -22.9 -15.7 -21.5 -26.5 -18.2 -23.3 -30.1 -20.4 -24.8 -33.6 -21.6 -26.0 -37.1 -21.9 -27.1 -40.3 -22.1 -27.8 -43.1 -22.2 -28.3 -45.8 -22.3 -28.6 -48.4 -22.4 -28.7 -50.7 -22.6 -28.9 -52.9 -22.7 -28.9 -55.0 -22.7 -29.0 -56.8 -22.8 -29.2 -58.7 -22.9 -29.2 -60.0 -22.9 -29.3 -61.2 -23.0 -29.5 -62.4 -23.0 -29.5 -63.1 -23.1 -29.6 -63.8 -23.2 -29.7 -64.4 -23.2 -29.8 -65.1 -23.3 -29.9 -65.8 -23.3 Rev. 1.1 November 2009 Maximum -5.0 -9.9 -14.6 -19.2 -23.6 -28.0 -32.2 -35.8 -39.5 -43.2 -46.7 -50.0 -53.1 -56.1 -58.7 -61.4 -63.5 -65.6 -67.7 -69.8 -71.6 -73.3 -74.9 -76.4 -77.7 -78.8 -79.7 ...

Related keywords