K9F1208U0M- SAMSUNG [Samsung semiconductor], K9F1208U0M- Datasheet - Page 37
![no-image](/images/no-image-200.jpg)
K9F1208U0M-
Manufacturer Part Number
K9F1208U0M-
Description
64M x 8 Bit NAND Flash Memory
Manufacturer
SAMSUNG [Samsung semiconductor]
Datasheet
1.K9F1208U0M-.pdf
(41 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
K9F1208U0M-PCB0
Manufacturer:
SAMSUNG
Quantity:
12 740
READ STATUS
The device contains a Status Register which may be read to find out whether program or erase operation is completed, and whether
the program or erase operation is completed successfully. After writing 70h command to the command register, a read cycle outputs
the content of the Status Register to the I/O pins on the falling edge of CE or RE, whichever occurs last. This two line control allows
the system to poll the progress of each device in multiple memory connections even when R/B pins are common-wired. RE or CE
does not need to be toggled for updated status. Refer to table 2 for specific Status Register definitions. The command register
remains in Status Read mode until further commands are issued to it. Therefore, if the status register is read during a random read
cycle, a read command(00h or 50h) should be given before sequential page read cycle.
For Read Status of Multi Plane Program/Erase, the Read Multi-Plane Status command(71h) should be used to find out whether
multi-plane program or erase operation is completed, and whether the program or erase operation is completed successfully. The
pass/fail status data must be checked only in the Ready condition after the completion of Multi-Plane program or erase operation.
Table3. Read Staus Register Definition
NOTE :
Read ID
The device contains a product identification mode, initiated by writing 90h to the command register, followed by an address input of
00h. Four read cycles sequentially output the manufacture code(ECh), and the device code (76h), Reserved(A5h), Multi plane oper-
ation code(C0h) respectively. A5h must be don’t-cared. C0h means that device supports Multi Plane operation. The command regis-
ter remains in Read ID mode until further commands are issued to it. Figure 22 shows the operation sequence.
K9F1208U0M-YCB0, K9F1208U0M-YIB0
Figure 22. Read ID Operation
CLE
CE
WE
ALE
RE
I/O
I/O No.
0
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
~
7
1. I/O 0 describes combined Pass/Fail condition for all planes. If any of the selected multiple pages/blocks fails in Program/
2. The pass/fail status applies only to the corresponding plane.
Erase operation, it sets "Fail" flag.
Plane 0 Pass/Fail
Plane 1 Pass/Fail
Plane 2 Pass/Fail
Plane 3 Pass/Fail
Device Operation
90h
Total Pass/Fail
Write Protect
Reserved
Status
Address. 1cycle
00h
Pass : "0"
Must be don’t -cared
Must be don’t -cared
Must be don’t -cared
Must be don’t -cared
Must be don’t -cared
Busy : "0"
Protected : "0"
t
CLR
t
Definition by 70h Command
WHR
t
AR1
t
CEA
t
REA
37
Not Protected : "1"
Maker code
Fail : "1"
Ready : "1"
ECh
Device code
76h
Pass : "0"
Pass : "0"
Pass : "0"
Pass : "0"
Pass : "0"
Must be don’t-cared
Busy : "0"
Protected : "0"
Definition by 71h Command
FLASH MEMORY
(1)
(2)
(2)
(2)
(2)
A5h
Not Protected : "1"
Fail : "1"
Ready : "1"
Fail : "1"
Fail : "1"
Fail : "1"
Fail : "1"
Multi-Plane code
C0h