AT25DL081-SSHN-T Adesto Technologies, AT25DL081-SSHN-T Datasheet - Page 3

• Manufacturer Part Number: AT25DL081-SSHN-T
• Description: Flash 8M 1.65-1.95V 100Mhz Serial Flash
• Manufacturer: Adesto Technologies

Specifications of AT25DL081-SSHN-T

• Rohs: yes
• Data Bus Width: 8 bit
• Memory Type: Flash
• Memory Size: 8 Mbit
• Architecture: Flexible, Uniform Erase
• Timing Type: Synchronous
• Interface Type: SPI
• Supply Voltage - Max: 1.95 V
• Supply Voltage - Min: 1.65 V
• Maximum Operating Current: 20 mA
• Operating Temperature: - 40 C to + 85 C
• Mounting Style: SMD/SMT
• Package / Case: SOIC-8

2.
Pin Descriptions and Pinouts
Table 2-1.
Symbol
CS
SCK
SI (SIO)
SO (SOI)
WP
Pin Descriptions
A high-to-low transition on the CS pin is required to start an operation and a
Name and Function
Chip Select: Asserting the CS pin selects the device. When the CS pin is
deasserted, the device will be deselected and normally be placed in standby
mode (not Deep Power-Down mode) and the SO pin will be in a high-impedance
state. When the device is deselected, data will not be accepted on the SI pin.
low-to-high transition is required to end an operation. When ending an internally
self-timed operation, such as a program or erase cycle, the device will not enter
the standby mode until the completion of the operation.
Serial Clock: This pin is used to provide a clock to the device and is used to
control the flow of data to and from the device. Command, address, and input data
present on the SI pin is always latched in on the rising edge of SCK, while output
data on the SO pin is always clocked out on the falling edge of SCK.
Serial Input (Serial Input/Output): The SI pin is used to shift data into the
device. The SI pin is used for all data input including command and address
sequences. Data on the SI pin is always latched in on the rising edge of SCK.
With the Dual-Output Read Array command, the SI pin becomes an output pin
(SIO) to allow two bits (on the SO and SIO pins) of data to be clocked out on every
falling edge of SCK. To maintain consistency with SPI nomenclature, the SIO pin
will be referenced as SI throughout this document except for those sections
dealing with the Dual-Output Read Array command, in which it will be referenced
as SIO.
Data present on the SI pin will be ignored whenever the device is deselected (CS
is deasserted).
Serial Output (Serial Output/Input): The SO pin is used to shift data out from the
device. Data on the SO pin is always clocked out on the falling edge of SCK.
With the Dual-Input Byte/Page Program command, the SO pin becomes an input
pin (SOI) to allow two bits (on the SOI and SI pins) of data to be clocked in on
every rising edge of SCK. To maintain consistency with nomenclature, the SOI pin
will be referenced as SO throughout this document except for those sections
dealing with the Dual-Input Byte/Page Program command in which it will be
referenced as SOI.
The SO pin will be in a high-impedance state whenever the device is deselected
(CS is deasserted).
Write Protect: The WP pin controls the hardware locking feature of the device.
See “Protection Commands and Features” on page 21
protection features and the WP pin.
The WP pin is internally pulled-high and may be left floating if hardware controlled
protection will not be used. However, it is recommended that the WP pin also be
externally connected to VCC whenever possible.
for more details on
AT25DL081 [DATASHEET]
Asserted
8732E–DFLASH–1/2013
State
Low
Low
—
—
—
Input/Output
Input/Output
Type
Input
Input
Input
3