C8051F996-GUR Silicon Labs, C8051F996-GUR Datasheet - Page 91
C8051F996-GUR
Manufacturer Part Number
C8051F996-GUR
Description
8-bit Microcontrollers - MCU 8kB ADC 14-CH CDC
Manufacturer
Silicon Labs
Datasheet
1.C8051F986-GUR.pdf
(322 pages)
Specifications of C8051F996-GUR
Rohs
yes
Core
8051
Processor Series
C8051
Data Bus Width
8 bit
- Current page: 91 of 322
- Download datasheet (2Mb)
7.
C8051F99x-C8051F98x devices include an on-chip programmable voltage comparator: Comparator 0
(CPT0) shown in Figure 7.1.
The Comparator offers programmable response time and hysteresis, an analog input multiplexer, and two
outputs that are optionally available at the Port pins: a digital synchronous “latched” output (CP0), or a
digital asynchronous “raw” output (CP0A). The asynchronous CP0A signal is available even when the
system clock is not active. This allows the Comparator to operate and generate an output when the device
is in some low power modes.
7.1.
Each Comparator performs an analog comparison of the voltage levels at its positive (CP0+) and negative
(CP0-) input. The analog input multiplexers are completely under software control and configured using
SFR registers. See Section “7.6. Comparator0 Analog Multiplexer” on page 96 for details on how to select
and configure Comparator inputs.
Important Note About Comparator Inputs: The Port pins selected as Comparator inputs should be
configured as analog inputs and skipped by the Crossbar. See the Port I/O chapter for more details on how
to configure Port I/O pins as Analog Inputs. The Comparator may also be used to compare the logic level
of digital signals, however, Port I/O pins configured as digital inputs must be driven to a valid logic state
(HIGH or LOW) to avoid increased power consumption.
Comparator
Comparator Inputs
P1.0
P1.1
Figure 7.1. Comparator 0 Functional Block Diagram
CP0HYN1
CP0HYN0
CP0HYP1
CP0HYP0
CP0OUT
CP0RIF
CP0FIF
CP0EN
CP0 +
CP0 -
+
-
Rev. 1.1
VDD
Px.x
GND
Decision
C8051F99x-C8051F98x
Reset
CPT0MD
Tree
(ASYNCHRONOUS)
(SYNCHRONIZER)
D
SET
CLR
Q
Q
D
SET
CLR
Q
Q
Rising-edge
CP0
Crossbar
Interrupt
Logic
Falling-edge
Interrupt
CP0
CP0A
CP0
CP0
91
Related parts for C8051F996-GUR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT EVALUATION FOR CP2102
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT EVAL FOR CP2103 USB TO UART
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT EVAL FOR CP2201 ETH CTRLR
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DAUGHTER CARD CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT STARTER CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F320/F321
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEVKIT-F120/21/22/23/24/25/26/27
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F310/F311
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT F220/221/226/230/231/236
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT F300/301/302/303/304/305
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F330/F331
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR F005/006/007
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR F020/F021/F022/F023
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT DEV FOR C8051F34X
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT DEV FOR C8051F41X
Manufacturer:
Silicon Laboratories Inc
Datasheet: