ATMEGA16U2-16AU Atmel, ATMEGA16U2-16AU Datasheet - Page 136

• Manufacturer Part Number: ATMEGA16U2-16AU
• Description: 8-bit Microcontrollers - MCU 16K Flash
• Manufacturer: Atmel

Specifications of ATMEGA16U2-16AU

• Product Category: 8-bit Microcontrollers - MCU
• Rohs: yes
• Core: AVR
• Data Bus Width: 8 bit
• Program Memory Size: 16 KB
• Data Ram Size: 1.25 KB
• Data Rom Size: 512 B
• Program Memory Type: Flash
• Factory Pack Quantity: 1250

16.11.10 TIFR1 – Timer/Counter1 Interrupt Flag Register
7799D–AVR–11/10
• Bit 5 – ICIEn: Timer/Countern, Input Capture Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally
enabled), the Timer/Countern Input Capture interrupt is enabled. The corresponding Interrupt
Vector
Bit 3 – OCIEnC: Timer/Countern, Output Compare C Match Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally
enabled), the Timer/Countern Output Compare C Match interrupt is enabled. The corresponding
Interrupt Vector
TIFRn, is set.
• Bit 2 – OCIEnB: Timer/Countern, Output Compare B Match Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally
enabled), the Timer/Countern Output Compare B Match interrupt is enabled. The corresponding
Interrupt Vector
TIFRn, is set.
• Bit 1 – OCIEnA: Timer/Countern, Output Compare A Match Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally
enabled), the Timer/Countern Output Compare A Match interrupt is enabled. The corresponding
Interrupt Vector
TIFRn, is set.
• Bit 0 – TOIEn: Timer/Countern, Overflow Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally
enabled), the Timer/Countern Overflow interrupt is enabled. The corresponding Interrupt Vector
(See “Interrupts” on page
• Bit 5 – ICFn: Timer/Countern, Input Capture Flag
This flag is set when a capture event occurs on the ICPn pin. When the Input Capture Register
(ICRn) is set by the WGMn[3:0] to be used as the TOP value, the ICFn Flag is set when the
counter reaches the TOP value.
ICFn is automatically cleared when the Input Capture Interrupt Vector is executed. Alternatively,
ICFn can be cleared by writing a logic one to its bit location.
• Bit 3 – OCFnC: Timer/Countern, Output Compare C Match Flag
This flag is set in the timer clock cycle after the counter (TCNTn) value matches the Output
Compare Register C (OCRnC).
Note that a Forced Output Compare (FOCnC) strobe will not set the OCFnC Flag.
OCFnC is automatically cleared when the Output Compare Match C Interrupt Vector is exe-
cuted. Alternatively, OCFnC can be cleared by writing a logic one to its bit location.
Bit
0x16 (0x36)
Read/Write
Initial Value
(See “Interrupts” on page
(See “Interrupts” on page
(See “Interrupts” on page
(See “Interrupts” on page
R
7
–
0
64.) is executed when the TOVn Flag, located in TIFRn, is set.
R
6
–
0
64.) is executed when the ICFn Flag, located in TIFRn, is set.
ICF1
R/W
5
0
64.) is executed when the OCFnC Flag, located in
64.) is executed when the OCFnB Flag, located in
64.) is executed when the OCFnA Flag, located in
R
4
–
0
ATmega8U2/16U2/32U2
OCF1C
R/W
3
0
OCF1B
R/W
2
0
OCF1A
R/W
1
0
TOV1
R/W
0
0
TIFR1
136